Vermont Casting 2080 사용자 설명서
14
WinterWarm Small Insert
2000888
Maintenance
Keep Your WinterWarm Small Insert Look-
ing New and Working Its Best
Care of the Cast Iron Surface
An occasional dusting with a dry rag will keep the
painted cast iron of your WinterWarm Small Insert look-
ing new.
If the paint needs retouching, first allow the surface to
cool completely. Mask glass, trim parts and enamelled
areas. Wire-brush those areas needing to be painted.
Touch-up with high temperature stove paint available
from your local dealer. Apply the paint sparingly. Two
light coats are better than one heavy one.
painted cast iron of your WinterWarm Small Insert look-
ing new.
If the paint needs retouching, first allow the surface to
cool completely. Mask glass, trim parts and enamelled
areas. Wire-brush those areas needing to be painted.
Touch-up with high temperature stove paint available
from your local dealer. Apply the paint sparingly. Two
light coats are better than one heavy one.
Care of the Porcelain Enamel Surface
Use a soft brush as necessary. Do not use water or
other liquids on your WinterWarm Small Insert. Finger-
prints usually can be buffed off porcelain enamel with a
dry, soft cloth. If marks remain, allow the WinterWarm
Small Insert to cool completely, then buff with a slightly
damp, soft cloth. Dry completely before starting a fire to
avoid streaking.
Never use abrasives or harsh chemical cleaners on the
porcelain enamel finish; the enamel may scratch and
expose the cast iron, which can then stain or rust. If
you must remove spills or stains from porcelain surfac-
es, make sure the fire is out and the WinterWarm Small
Insert has cooled completely before cleaning. Use a
kitchen appliance cleaner and/or polish specially formu-
lated for enamel surfaces. Apply the cleaner sparingly
with a soft cloth, and buff away all traces.
other liquids on your WinterWarm Small Insert. Finger-
prints usually can be buffed off porcelain enamel with a
dry, soft cloth. If marks remain, allow the WinterWarm
Small Insert to cool completely, then buff with a slightly
damp, soft cloth. Dry completely before starting a fire to
avoid streaking.
Never use abrasives or harsh chemical cleaners on the
porcelain enamel finish; the enamel may scratch and
expose the cast iron, which can then stain or rust. If
you must remove spills or stains from porcelain surfac-
es, make sure the fire is out and the WinterWarm Small
Insert has cooled completely before cleaning. Use a
kitchen appliance cleaner and/or polish specially formu-
lated for enamel surfaces. Apply the cleaner sparingly
with a soft cloth, and buff away all traces.
Cleaning the Glass
The WinterWarm Small Insert glass system requires
a minimum amount of cleaning. Most carbon deposits
that accumulate will burn off during hot fires.
Ash residue that accumulates on the glass should be
removed periodically to prevent etching. To clean the
glass, use the following procedure.
a minimum amount of cleaning. Most carbon deposits
that accumulate will burn off during hot fires.
Ash residue that accumulates on the glass should be
removed periodically to prevent etching. To clean the
glass, use the following procedure.
•
Be sure the glass is completely cool.
•
Cleaning with water will work in most cases. Use
a glass cleaner especially made for this purpose
only if deposits are specially heavy. (If heavy
deposits are a frequent occurrence, however,
evaluate your operating techniques.) Do not use
abrasive cleaners.
a glass cleaner especially made for this purpose
only if deposits are specially heavy. (If heavy
deposits are a frequent occurrence, however,
evaluate your operating techniques.) Do not use
abrasive cleaners.
•
Rinse the glass thoroughly.
•
Dry the glass completely.
NOTE: The WinterWarm Small Insert glass is
coated with a special material on one side that
helps reflect heat back into the fire chamber. Do
not attempt to remove this coating.
coated with a special material on one side that
helps reflect heat back into the fire chamber. Do
not attempt to remove this coating.
Adjust the Door Latch Periodically
The front door of the WinterWarm Small Insert should
close securely to prevent accidental opening and
should close tightly to prevent air from leaking into the
fire chamber. The door handle will be positioned verti-
cally when the door is closed.
Over a period of time, the gasket around the door will
compress and the latch may need adjustment. To ad-
just the handle, follow this procedure:
1. Loosen the small lock nut with a 7/16” wrench. (Fig.
close securely to prevent accidental opening and
should close tightly to prevent air from leaking into the
fire chamber. The door handle will be positioned verti-
cally when the door is closed.
Over a period of time, the gasket around the door will
compress and the latch may need adjustment. To ad-
just the handle, follow this procedure:
1. Loosen the small lock nut with a 7/16” wrench. (Fig.
14)
2. Extend the striker screw one turn by turning it with a
1/8” Allen wrench.
3. Re-tighten the lock nut, while at the same time hold-
ing the striker screw with the Allen wrench to prevent
its turning.
its turning.
Test the door seal. Close the door on a dollar bill and
attempt to pull it free. If the bill is freed with little re-
sistance, the gasket isn’t snug enough at that spot.
Continue to make small adjustments until the setting is
right.
If additional adjusting of the latch does not enable the
door to seal sufficiently in one area, try “adjusting” the
gasket in that area. Pack more cement or a smaller
diameter gasket into the channel beneath the gasket so
the main gasket is raised and makes contact with the
door frame. If this procedure doesn’t solve the problem,
replace the gasket. Instructions for gasket replacement
are given later in this section.
attempt to pull it free. If the bill is freed with little re-
sistance, the gasket isn’t snug enough at that spot.
Continue to make small adjustments until the setting is
right.
If additional adjusting of the latch does not enable the
door to seal sufficiently in one area, try “adjusting” the
gasket in that area. Pack more cement or a smaller
diameter gasket into the channel beneath the gasket so
the main gasket is raised and makes contact with the
door frame. If this procedure doesn’t solve the problem,
replace the gasket. Instructions for gasket replacement
are given later in this section.
ST531
Door Pawl
11/00
Pawl
Small
Locking Nut
Large
Locking
Nut
Set Screw
Striker Screw
Handle Stub
ST531
Fig. 14 Turn the door latch striker screw in or out to tighten or
loosen the door latch.
loosen the door latch.