Quadra-Fire CASTINS-CSB 사용자 설명서
Page 32
250-7251G
August 20, 2009
R
Castile Pellet Insert
3. Cleaning Firepot with Cleaning Rod & Firepot
Scraper
•
Frequency: Daily or more often as needed
•
By: Homeowner
a. The appliance must be in complete shutdown and cool
and the exhaust blower off. If you are just cleaning the
fi repot, there is no need to unplug the appliance.
fi repot, there is no need to unplug the appliance.
b. Pull fi repot cleaning rod OUT a couple of times to help
shake debris loose. See Figure 33.1 on page 33. If rod
is hard to pull, it may be necessary to use your fi repot
clean-out tool to chip away material that has built up
on the bottom plate of the fi repot and to push out any
clinkers. Larger clinkers may have to be removed from
the top of the fi repot. Corn clinkers can be especially
diffi cult to break up.
is hard to pull, it may be necessary to use your fi repot
clean-out tool to chip away material that has built up
on the bottom plate of the fi repot and to push out any
clinkers. Larger clinkers may have to be removed from
the top of the fi repot. Corn clinkers can be especially
diffi cult to break up.
c. The firepot floor plate must be fully closed when
fi nished. See Figure 26.2 on page 26.
WARNING
• NEVER pull fi repot cleaning rod or cleaning
slide plates out when appliance is operating.
• The cleaning slide plates must be fully
CLOSED when appliance is operating.
•. Hot pellets may fall into ashpan and start a fi re
or mis-starts due to lack of vacuum.
Fire Risk
a. Loosen screw on top right corner directly under the cast
top, but do not remove. Figure 32.1.
b. With thumb, press upward on the frame to relieve the
pressure on the cast side. Figure 32.2.
c. Slide the cast side downward as shown in Figure 32.3.
(The top has been removed to show the details.
d. Lay sides on protective padding to avoid scratching the
paint or chipping the porcelain.
e. Repeat for the other side.
Front
Right
Cast
Side
Cast
Side
Top
CAST
SIDE
SIDE
Flex frame upward with thumb
to relieve pressure on cast side.
to relieve pressure on cast side.
Figure 32.1
Figure 32.2
Figure 32.3
2. Remove Cast Sides for Cleaning & Maintenance
4. Ash Removal from Firebox
•
Frequency: Weekly or more frequently depending on
ash build-up.
•
By: Homeowner
a. There must not be any hot ashes in the fi rebox during
cleaning so allow the appliance to completely cool.
The fi rebox ash should be removed every time the
fi repot is cleaned. Frequent cleaning of the ash in
the fi rebox will help slow down the build-up of ash in
the exhaust blower and vent system.
The fi rebox ash should be removed every time the
fi repot is cleaned. Frequent cleaning of the ash in
the fi rebox will help slow down the build-up of ash in
the exhaust blower and vent system.
b. Plug in your appliance, if unplugged, and turn the
thermostat on and immediatley shut it off to start the
exhaust blower on its cycle time. It will pull fl y ash
out the exhaust instead of into the room.
exhaust blower on its cycle time. It will pull fl y ash
out the exhaust instead of into the room.
c. Open cast hinged face. Directly underneath the
fi rebox door and to the left and right of the fi repot are
2 cleaning slide plates with fi nger holes. Pull both
slide plates out and then open the glass door. Sweep
the remaining ash from the fi rebox into the 2 open
holes. A paint brush works well for this. Close slide
plates.
2 cleaning slide plates with fi nger holes. Pull both
slide plates out and then open the glass door. Sweep
the remaining ash from the fi rebox into the 2 open
holes. A paint brush works well for this. Close slide
plates.
d. This ash is deposited in the same ash pan as the
fi repot debris. The ash pan should be emptied every
time you clean the fi rebox. Remember to place
the ash and debris into a metal or noncombustible
container.
time you clean the fi rebox. Remember to place
the ash and debris into a metal or noncombustible
container.