Marley Engineered Products 1800 사용자 설명서

This Heater is designed to provide years of efficient, trouble free
operation as a primary or supplementary heat source for residen-
tial  and  commercial  applications.  Baseboard  heaters  must  be
thermostatically controlled for efficient, safe operation.  A thermo-
stat is not provided with this heater.  However, a single or double

pole  thermostat  accessory  is  available  for  installation  into  this
heater at your place of purchase, or the heater may be connect-
ed to any suitable wall mounted thermostat that will meet the elec-
trical load requirements.  Installation or use of this product in any
manner  not  described  herein  will  void  the  warranty  and  could
result  in  injury,  damage  to  property,  or  permanent  damage  to
heater.

UNPACKING HEATER

Check heater to make sure it has not been damaged in shipping.
Do not install or attempt to operate the heater if damaged. Return
to place of purchase or file claim with freight carrier.

NOTICE TO OWNERS

Certain fabrics discolor in time from indirect sunlight and normal
room temperature - mostly organic and synthetic material.  They
will  discolor  more  rapidly  when  exposed  to  direct  sunlight  and
warm currents.  Hang drapes to provide minimum of 2 in.(51mm)
air space between heater front and nearest drape fold as shown
in Example 1 Figure 1, or 6 in.(153mm) airspace between top of
heater  and  bottom  of  drapes  as  shown  in  Example  2,  Figure  1.
Allow minimum clearance of 1 in. (26mm) from drapes to ceiling
and  to  top  of  floor  covering  to  permit  air  circulation  as  shown  in
Example 1, Figure 1.

INSTALLATION

FLOORS & CARPETING:
Heaters may be mounted directly on any floor surface, including
carpeting.  Where wall-to-wall carpets are installed after the base-
board  installation,  the  carpeting  can  be  run  up  to  the  front  and
around  the  heater  body,  providing  it  does  not  obstruct  air  flow.
(Maximum 3/4” (19mm) thick).
1.

Remove wiring compartment cover at end of heater where
power supply cable is to enter. Determine desired mounting
location (Figure 2), position heater to wall as intended and mark
wall (or floor) at location where power supply is to enter heater.

Heater Ampere Rating.

Total Amps

Minimum

AWG. Wire Size

(Copper)

Circuit Breaker

or Fuse Size

0 thru 12

12.1 thru 16
16.1 thru 24

#14
#12
#10

15 amp
20 amp
30 amp

NET VOLUMES OF WIRING COMPARTMENT

DESCRIPTION

CUBIC

INCHES

CUBIC

CENTIMETERS

Heater Only (Each Wiring Compartment)

Heater W/SP Thermostat

Heater W/DP Thermostat

Heater W/Heat-Cool Switch Receptacle

Heater W/Duplex Receptacle

Heater W/DP Disconnect Switch

Heater W/Power Relay

Heater W/Transformer Relay

14.96

11.18

9.51

11.18

10.76

2.93

241

180

153

180

174

Figure. 1 Position Drapery near Heater

Figure. 2

Residential

Model No.

2512 *

25126 *

2513 *

2514 *

2515 *

2516 *

2502 *

25026 *

2503 *

2504 *

2505 *

2506 *

2507 *

2508 *

25008 *

2542 *

25426 *

2543 *

2544 *

2545 *

2546 *

2547 *

2548 *

25408 *

2572 *

25726 *

2573 *

2574 *

2575 *

2576 *

2577 *

2578 *

25708 *

25326 *

2533 *

2534 *

2535 *

2536 *

2537 *

2538 *

25308 *

2530 *

2564 *

2565 *

2566 *

2567 *

2568 *

25608 *

2560 *

C25126 *

C2513 *

C2514 *

C2515 *

C2516 *

C25026 *

C2503 *

C2504 *

C2505 *

C2506 *

C2507 *

C2508 *

C25008 *

C25426 *

C2543 *

C2544 *

C2545 *

C2546 *

C2547 *

C2548 *

C25408 *

C25726 *

C2573 *

C2574 *

C2575 *

C2576 *

C2577 *

C2578 *

C25708 *

C25326 *

C2533 *

C2534 *

C2535 *

C2536 *

C2537 *

C2538 *

C25308 *

C2530 *

C2564 *

C2565 *

C2566 *

C2567 *

C2568 *

C25608 *

C2560 *

3.3

4.2

6.3

8.3

10.4

12.5

1.9

2.4

3.6

4.8

6.0

7.2

9.6

8.4

12.0

1.4

1.8

2.7

3.6

4.5

5.4

6.3

7.2

8.7

1.1

1.4

2.0

2.7

3.4

4.1

4.7

5.4

6.8

1.7

2.1

3.1

4.2

5.2

6.3

7.3

8.3

10.4

1.2

1.6

2.4

3.1

3.9

4.7

5.5

6.3

7.5

1.4

1.8

2.7

3.6

4.5

5.4

6.3

7.2

9.0

Commercial

Model No.

120

Volt

208 Volt 240 Volt 277 Volt

1.4

2.2

2.9

3.6

4.3

5.0

5.8

7.2

347 Volt

1.7

2.1

2.5

2.9

3.3

4.2

600 Volt

* Followed by WC or NWC suffix