RCA RT2870R 전단

It's important to read this instruction prior to using your new product for the fi rst time.

811-AV6291W073

EXPORTER

Printed in China

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful interference 
to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which can be determined 
by turning the equipment off  and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 

• 

connected.
Consult the dealer or an experienced radio / TV technician for help.

• 

WARNING: Changes or modifi cations to this unit not expressly approved by the party responsible for 
compliance could void the user's authority to operate the equipment.

This class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment 
Regulations.

The Shock Hazard Marking and Associated Graphical Symbol is provided on the bottom panel of unit.

Refer to the identification / rating label located on the back panel of your product for its proper 
operating voltage.

IMPORTANT: The power cord can be unplugged to turn off  the main power to the unit. It should also be 
easily accessible in an emergency.

Leave suffi

  cient space around the appliance to allow adequate ventilation: 10cm on either side and 

• 

at the back, as well as 7cm above it are ideal. 

WARNING: To reduce the risk of fi re or electric shock, do not expose this apparatus to rain or moisture.

Digital Input
Connect components, such as DVD players, Satellite receiver/
Cable boxes, BD (Blu-ray Disc

TM

) Players or TV’s, capable of 

outputting Dolby Digital (Surround Sound) or standard PCM 
(Stereo) format digital signals.
Note: “Blu-ray Disc” is a trademark of Blu-ray Disc Association.

Digital Connection
•  This unit provides two optical and one coaxial digital input jacks for the connection of your 

components that have digital audio outputs.

•  To connect DVD player, Satellite receiver, Cable box, Blu-ray Player, or TV that has a digital audio 

output, use a coaxial digital (included) or an optical digital cable (not included) to carry the audio 
signal and enjoy Dolby Digital sound quality.

•  A separate optical or coaxial cable is needed for each digital connection.

Speaker wires are color-coded to match the terminals. Connect the speaker wire from the back of each 
speaker to the corresponding color terminal at the back of the unit. Press down the tab to open the 
terminal and insert the wire. Release the tab to lock wire in the terminal.

When connecting the speakers, make sure the polarities (“+“ speaker wire to “+“ on the unit. For example, red 
wire to red terminal on the unit) of speaker wires and terminals match.

If the cords are reversed, the sound will be distorted. Do not let the speaker wires touch each other, it will 
damage the Home Theater’s amplifi er.

Place the rear speakers and subwoofer a 
foot or more away from TV when using 
the Front Surround sound Eff ect (FSsE).

Adjust the Angle of the Speakers
To achieve the best Front Surround sound Eff ect 
(FSsE), adjust the mounted front left and the rear 
left speakers to the left for an angle of 25

o

 - 45

o

 

from the center.

Adjust the mounted front right and rear right 
speakers to the right in the same way.

Disconnecting the Speakers
1.  To unlock the speakers, press and hold the 

hinge spring as illustrated below.

2.   Slide out the rear speaker from the hinge.
3.   Press and hold the two hinge springs.
4.   Slide out the hinge from the front speaker.

The digital audio jacks can accept Dolby Digital (Surround Sound) or PCM (Stereo) signals when compatible 
components are connected.

The AC power plug is polarized (one blade is 
wider than the other) and only fi ts into AC power 
outlets one way. If the plug won’t go into the outlet 
completely, turn the plug over and try to insert it 
the other way.
If it still won’t fi t, contact a qualifi ed electrician to 
change the outlet, or use a diff erent one. Do not 
attempt to bypass this safety feature.

To prevent electric shock, match wide blade of 

• 

plug to wide slot, fully insert.
Main plug is used as disconnect device and it 

• 

should remain readily operable during intended 
use. In order to disconnect the apparatus from 
the mains completely, the mains plug should 
be disconnected from the mains socket outlet 
completely.

This product should be serviced only by those 
specially trained in appropriate servicing 
techniques. For instructions on how to obtain 
service, refer to the warranty included in this user 
manual.

Make sure you connect all your other electronic 
components and the speakers before plugging 
your unit into the outlet. Plug the power cord in the 
wall outlet, matching the wide blade of the plug 
with the wide slot in the outlet. Be sure to insert 
the plug completely.

Product: Audio Receiver with Dolby Digital
Brand : RCA

Electrical Consumption
Power Supply: 120V ~ 60Hz
Power Consumption: 90 Watts

This Home Theater has earned 
the ENERGY STAR.

Do not play your headset at a high volume. 

• 

Hearing experts warn against extended high-
volume play.
If you experience a ringing in your ears, reduce 

• 

volume or discontinu use.
You should use extreme caution or temporarily 

• 

discontinue use in potentially hazardous 
situations.
Even if your headset is an open-air type 

• 

designed to let you hear outside sounds, 
don't turn up the volume so high that you are 
unable to hear what is around you.
Excessive sound pressure from earphones and 

• 

headphone can cause hearing loss.

THE LIGHTNING FLASH AND ARROWHEAD 
WITHIN THE TRIANGLE IS A WARNING 
SIGN  ALERTING YOU OF “DANGEROUS 
VOLTAGE” INSIDE THE PRODUCT.

THE EXCLAMATION POINT WITHIN THE  
TRIANGLE IS A WARNING SIGN ALERTING 
YOU OF IMPORTANT INSTRUCTIONS 
ACCOMPANYING THE PRODUCT.

Please read and save for future reference.

Some of the following information may not apply 
to your particular product; however, as with 
any electronic product, precautions should be 
observed during handling and use.

Read these instructions.

• 

Keep these instructions.

• 

Heed all warnings.

• 

Follow all instructions.

• 

Do not use this apparatus near water.

• 

Clean only with a dry cloth.

• 

Do not block any ventilation openings. Install in 

• 

accordance with the manufacturer’s instructions.
Do not install near any heat sources such 

• 

as radiators, heat registers, stoves, or other 
apparatus (Including amplifiers) that produce 
heat.
Do not defeat the safet y purpose of the 

• 

polarized or grounding-type plug. A polarized 
plug has two blades with one wider than the 
other. A grounding type plug has two blades 
and a third grounding prong. The wide blade or 
the third prong is provided for your safety.  If the 
provided plug does not fi t into your wall outlet, 
consult an electrician for replacement of the 
obsolete outlet.
Protect the power cord from being walked on 

• 

or pinched particularly at plugs, convenience 
receptacles, and the point where they exit from 
the apparatus.
Only use attachments / accessories specifi ed by 

• 

the manufacturer.
Use only with a cart, stand, tripod, bracket, or 

• 

table specifi ed by the manufacturer, or sold with 
the apparatus. When a cart is used, use caution 
when moving the cart / apparatus combination 
to avoid injury from tip-over.

Unplug this apparatus during lightning storms 

• 

or when unused for long periods of time.
Refer all servicing to qualifi ed service personnel. 

• 

Servicing is required when the apparatus has 
been damaged in any way, such as the power 
cord or plug is damaged, liquid has been spilled 
or objects have fallen into the apparatus, the 
apparatus has been exposed to rain or moisture, 
does not operate normally, or has been 
dropped.

Additional safety information
•  Apparatus shall not be exposed to dripping or 

splashing and no objects fi lled with liquids, such 
as vases, shall be placed on the apparatus.

•  Always leave suffi

    cient space around the product 

for ventilation. Do not place product in or on a bed, 
rug, in a bookcase or cabinet that may prevent air 
fl ow through vent openings.

•  Do not place lighted candles, cigarettes, cigars, 

etc. on the product.

•  Connect power cord only to AC power source as 

marked on the product.

•  Care should be taken so that objects do not fall 

into the product.

•  Do not attempt to disassemble the cabinet. This 

product does not contain customer serviceable 
components.

If your product operates on batteries, adhere to the 
following precautions:

A. Any battery may leak electrolyte if mixed with a 

diff erent battery type, inserted incorrectly, or if all 
batteries are not replaced at the same time.

B. Any battery may leak electrolyte or explode if 

disposed of in fi re or an attempt is made to charge 
a battery not intended to be recharged.

C. Discard leaky batteries immediately. Leaking 

batteries can cause skin burns or other personal 
injury. When discarding batteries, be sure to 
dispose of them in a proper manner, according 
to your state/provincial and local regulations.

D. Battery shall not be exposed to excessive heat 

such as sunshine, fi re or the like.

]

•  One main unit
•  One remote control with batteries
•  One pair of front speakers, one pair of rear speakers, 

one center speaker and one subwoofer

•  One pair of front speaker stands (for use in Front 

Surround Sound Confi guration only)

•  One pig-tail antenna wire
•  One AM loop antenna
•  One coaxial digital cable
•  One pair of audio cable for analog connections
•  One English & one Spanish user manuals

Provides spaces for suffi

  cient  ventilation  as 

indicated: 

•  Do not connect to the AC power cords until all 

connections are completed.

•  Do not use your set immediately after transferring 

it from a cold place to a warm place: there is risk 
of condensation.

•  Do not expose your set to water and excessively 

high temperatures.

•  After having disconnected your set, clean the 

case with a soft cloth, or with a slightly damp 
leather chamois. Never using strong solvents.

•  Do not block ventilation holes in any component. 

Arrange the components so that air can circulate 
freely.

•  Do not stack components directly on top of each 

other.

•  Do not place the unit near other components 

that generate heat such as heating vents.

•  Allow adequate ventilation when placing your 

components in a stand.

•  Place an amplifi er near the top shelf of the stand 

so heated air rising from it will not aff ect other 
components. If you have a satellite receiver, you 
should place it on the top shelf.

Note: Optical and coaxial cables carry only the audio portion of the signal.

Main unit

GAME

GAME

 Front
speaker 
 stands 

Left and right

front speakers

Left and right
rear speakers

Subwoofer

Center speaker

Coaxial digital

cable

Audio cable for 
analog connections

Pig-tail

antenna wire

Remote

control with

batteries

AM loop antenna

User manual

DVD      SAT / CAB     BD

SAT

BD

BD

DVD     SAT / CAB     BD

COAXIAL  OPTICAL1  OPTICAL2

 

Optical Digital In (Audio)
Connect to optical digital output of Cable box, Satellite receiver, DVD, Blu-ray player, 
TV or other compatible devices using the Optical Fiber Cable (not included).

Coaxial Digital In (Audio)
Connect to coaxial digital output of DVD, Cable box, Satellite
receiver, TV or other compatible devices using the Coaxial Digital
Cable (included).

BD/DVD/SAT/CAB/TV/GAME

BD/DVD/SAT/CAB/TV/GAME

BD/DVD/SAT/CAB/TV/GAME

Cable box

DVD player

Connect the AM and FM antennas to the AM and FM terminals on the system’s back panel.

They must be hooked up in order to receive clear reception. For FM reception, extend antenna to its full 
length. For AM reception, rotate the antenna horizontally to get better reception.

AM Loop Antenna and FM Indoor Antenna
1.  Uncoil the antenna wire and locate the base end of the AM antenna.
2.  Press down on the antennas tab to open the  terminal.
3.  Insert the antenna wires into the terminal and release the tabs to secure the wires in place.
4.  Make sure the white wire on the AM loop antenna is inserted into the AM loop terminal and the other 

wire is inserted into the ground loop terminal.

3

3

1

1

2

4

Courtesy Dolby Laboratories

Note: Place the rear speakers and 
subwoofer a foot or more away from 

TV when using the Front Surround sound 
Eff ect (FSsE).

1. Left, Right (Front Speakers)
Front speakers carry primarily music and sound 
eff ects.

2. Center
In surround mode, the center speaker carries most 
of the dialog as well as music and eff ects.
It should be set between the left and right 
speakers.

3. Surround (Rear Speakers)
The surround speakers’ overall sound balance 
should be as close as possible to the front speakers. 
Proper placement is vital to establish an evenly 
distributed sound fi eld.

4. Subwoofer
A subwoofer is designed to reproduce powerful 
low bass eff 

ects (explosions, the rumble of 

spaceships, etc.).

Speakers placed less than two feet from the TV set 
must be magnetically shielded in order to prevent 
picture distortion. Center speaker provided with 
this unit is magnetically shielded to protect your 
TV set.

For best results, follow the speaker placement 
below.

Alignment
Align the center speaker evenly with (A) or slightly 
behind (B) (the left and right speakers), but not 
ahead of them.

Angle
Place the left and right speakers to form a 45-
degree angle with your favorite viewing position 
to duplicate the soundtrack mixer’s perspective.

Height
The three front speakers should be as close as 
possible to the same height. This often requires 
placing the center speaker directly on top (A) or 
beneath (B) the TV set.

A

B

Courtesy Dolby Laboratories

Courtesy Dolby Laboratories

Courtesy Dolby Laboratories

Courtesy Dolby Laboratories

Location
If possible, place surround speakers to either side of 
the listening area, not behind it.

Height
If space permits, install surround speakers 2-3 feet 
above viewers. This helps to minimize localization 
eff ects.

Aiming
Aim surround speakers straight across the room, 
not down at viewers, to help create a more open, 
spacious surround sound fi eld.

Confi guration 1
Follow the suggestion for speaker placement in the 
section before.

Rear wall
If rear wall mounting is the only choice, aim the 
speakers at each other (A), towards the front (B) or 
towards the sidewalls (C, D).
Experiment with placement until sounds seem to 
surround you, rather than come from behind you.

No adjacent walls
Surround speakers can go on stands facing each 
other to approximate sidewall mounting (A), or to 
the sides or rear of the viewing area, aimed upwards; 
they can go right on the fl oor, or preferably, a few 
feet off  the fl oor such as on end tables (B).

1

1

Confi guration 2
If placing the rear speakers (surround speakers) at 
the back is not a good choice for you, you can use 
the Front Surround sound Eff ect (FSsE). Follow the 
following instruction for setting the speakers. 

Mounting the Speakers
-  Place the front speaker upside down and attach 

the supplied speaker stands to the top of the 
front speakers.

-  Slide in the hinge to the bottom of the front 

speaker until the 'click' sound is heard.

-  Slide in the rear speaker to the hinge until the 

'click' sound is heard.

Note: Match the front left and rear left 
speakers together and match the front 

right and rear right speakers together.

Front

Speaker

1

2

Top

Hinge

Bottom

Speakers stand

Rear

Speaker

Front

Speaker

Rear

Speaker

Front

Speaker

Rear

Speaker

Front

Speaker

3

4

Press

and

hold

1

2

Hinge Spring

3

4

Press

and
hold

Hinge Spring

2

After adjusting the 
angle, the speaker 
should look like this 
illustration.

User Manual

GAME

GAME

- 1 -

- 9 -

- 8 -

- 7 -

- 10 -

- 5 -

- 4 -

- 3 -

- 6 -

- 2 -

CAUTION: TO REDUCE THE RISK OF ELECTRIC 
SHOCK, DO NOT REMOVE COVER (OR BACK). 
NO USER SERVICEABLE PARTS INSIDE. 
REFER SERVICING TO QUALIFIED SERVICE 
PERSONNEL.

Right

Left

Rear Speakers

(Surround Sound)

Blue and Black

Grey and Black

Subwoofer

Purple and Black

White and 

Black

Red and 

Black

Right

Left

Front Speakers

Center Speaker

Green and Black

Use this jack on
the rear panel
to connect an
active subwoofer
other than the 
one supplied.

SUBWOOFER

AUDIO OUT

Note: If your TV has digital audio output, you can connect it 
to one the unit’s digital audio inputs, instead of using analog 
connection.