Little Wonder 5612-00-01 사용자 설명서

1.  Remove Collector assembly, Nozzle assembly, and 

debris bag from the top section of the package.

2.  Remove cardboard insert.

3.  Cut away short side of the box and fold down.
4.  Roll HPV base unit out of the box.

1.  Attach the 

collector assembly to the base unit:

  •Bolt the collector assembly to the frame with 4 sets 

of bolts, nuts, and 3 washers.  Attach rope guide 

with upper right bolt.

  •Slide the rectangular end of the collector over 

the housing and mount the flange with 2 sets of 

washers and nuts.

2.  Attach the throttle cable bracket to the handle with a 

1/4-20 thread rolling screw A.  Tighten until snug, but 

do not overtighten.  Intall throttle cable assembly to 

handle with 1/4-20x2 bolt, 2 washers, and 1/4 nylon 

locknut.

  •Secure throttle cable to handle with 

cable ties in 2 

places.

3.  Install the 

band clamp into the debris bag (wear 

gloves when handling band clamp):

  •Slide the bracket end of the band clamp through the 

left side opening of the sleeve on the debris bag 

until it emerges from the right side.

  •Feed the tail end of the band (on the clasp side) 

behind the bracket in the sleeve.

  •Pinch the wire form on the clasp together and 

connect it through 2 holes in the adjustment bracket 

such that it will close tightly over the collector.

4.  Connect the 

debris bag by placing it over the bottom 

lip of the 

collector and closing the clasp to secure the 

bag.  Adjust the clasp wire form to the appropriate hole 

position on the bracket to insure a tight fit. If the bag 

will not fit tight within the range of the 3 adjustment 

holes, insert the bag 

seal strap:

  •Unhook the wire form from the bracket. 

  •Pull the tail end of the band back out from behind 

the bracket.

  •Feed one end of the 

seal strap behind the metal 

band and through the channel to the other side.

  •Tuck the other end of the 

seal strap behind the 

bracket (overlapping the lead end of the 

seal strap).

  •Feed the tail end of the 

band clamp behind the 

bracket (overlap the 

seal strap).

  •Connect the wire form to the appropriate holes in the 

bracket and secure the debris bag to the collector.

5. Attach 

nozzle assembly to base unit:

  •Attach one end of the 

hose to the nozzle assembly 

with the 

  •Slide the other end of the 

hose over the edge of the 

inlet on the 

  •Hook one side of the 

nozzle bracket over the front 

axle.

  •Bend the other end of the nozzle bracket inward to 

hook it over the axle and engage the pins on the 

wheel bracket with the slots on the nozzle bracket.

  •Secure the hose to 

front plate inlet with the bridge 

  •Attach the 

nozzle cable end fitting through the hole 

in the 

6.  To remove 

nozzle assembly (for purposes of storage, 

or clearing blockages):

  •Turn engine off and disconnect spark plug.

  •Loosen 

hose clamp on the front plate with flathead 

screwdriver or 5/16 wrench.

  •Slide hose off of 

front plate inlet.

  •Bend one side of 

nozzle bracket inward and twist 

the 

assembly to remove the hook from the axle. 

  •Twist back and lift to remove the other side of 

nozzle bracket from the axle.

The Little Wonder HPV Vac includes a convenient lifting 

lug 

A on top of the fan housing that can be used to lift 

the unit.  This lug can only hold up to a total of 250 lbs     

(115 kg).