Panasonic RP-BTD10 사용자 설명서
VQT5J78
8
8
Before requesting service, make the following checks. If you are in doubt about
some of the check points, or if the remedies indicated in the chart do not solve
the problem, refer to “Customer Services Directory (United States and Puerto
Rico)” on page 10 if you reside in the U.S.A. or Puerto Rico, or refer to “CONTACT
INFORMATION” on page 11 if you reside in Canada.
some of the check points, or if the remedies indicated in the chart do not solve
the problem, refer to “Customer Services Directory (United States and Puerto
Rico)” on page 10 if you reside in the U.S.A. or Puerto Rico, or refer to “CONTACT
INFORMATION” on page 11 if you reside in Canada.
General
The unit does not respond
• Press RESET hole while connecting the USB charging cord to the charging
terminal (DC IN). (
→ P. 5)
Power supply and charging
Cannot charge the unit
• Make sure the computer is turned on and is not on standby or sleep mode.
• Is the USB port you are currently using working properly? If your computer has
other USB ports, unplug the connector from its current port and plug it into one of
the other ports.
the other ports.
• If the measures mentioned above are not applicable, unplug the USB charging
cord and plug it in again.
• Is the LED blinking in red ? There is a charging malfunction if the LED is blinking.
• If the LED is blinking fast in red even when the unit is being recharged in a room
temperature within 10 °C and 35 °C (50 ºF and 95 ºF), the battery may have run
down. (Number of recharging times of the included battery: Approximately 500.)
down. (Number of recharging times of the included battery: Approximately 500.)
LED does not light during charging / Charging takes longer
• Is the USB charging cord (supplied) connected firmly to the USB terminal of the
computer? (
→ P. 3)
The power does not turn on
• Is the unit being charged? The power cannot be turned ON during charging.
(
→ P. 3)
• Is the detachable cord connected? The power cannot be turned on when the
detachable cord is connected to the unit.
Troubleshooting guide
Bluetooth
®
device connection
The device cannot be connected
• Delete the pairing information for this unit from the Bluetooth
®
device, then pair
them again. (
→ P. 3)
Sound and audio volume
No sound
• Make sure that the unit and the Bluetooth
®
device are connected correctly. (
→ P. 3)
• Check if music is playing on the Bluetooth
®
device.
• Make sure that the unit is turned on and the volume is not set too low.
• Pair and connect the Bluetooth
®
device and the unit again. (
→ P. 3)
Low volume
• Increase the volume of the unit. (
→ P. 4)
• Increase the volume on the Bluetooth
®
device.
Sound from the device is cut off / Sound quality is bad
• Sound may be disrupted if signals are blocked. Do not fully cover this unit with
the palm of your hand, etc.
• The device may be out of the 10 m (33 feet) communication range. Move the
device closer to this unit.
• Remove any obstacle between this unit and the device.
• Switch off any wireless LAN device when not in use.
• A communication problem may arise if the battery is not fully charged. Charge
the unit. (
→ P. 3)
Phone Calls
You cannot hear the other person
• Make sure that the unit and the Bluetooth
®
enabled phone are turned on.
• Check if the unit and the Bluetooth
®
enabled phone are connected. (
→ P. 3)
• Check the audio settings of the Bluetooth
®
enabled phone. Switch the calling
device to the unit if it is set to the Bluetooth
®
enabled phone. (
→ P. 3)
• If the volume of the other person’s voice is too low, increase the volume of both
the unit and the Bluetooth
®
enabled phone.