Marantz CR601 사용자 설명서

7 Confirm and change timer

• You can check and change the timer program

setting as follows.

Press the 

button 

x

.

Either turn the 

4

/

¢

knob 

!5

or

press the 

5

or 

∞

button 

c

to select timer

program number.

You can change the displayed contents with the

4

/

¢

knob 

!5

or 

5

or 

∞

button

c

and 

buttons 

b

if necessary.

• Timer program is not changed if you quit

confirming halfway through a procedure.

7 Timer program off

Press the 

button 

x

,  “

” is displayed.

Either turn the 

4

/

¢

knob 

!5

or

press the 

5

or 

∞

button 

c

to select timer

program number.

Press the 

4

/

¢

knob 

!5

or

button 

b

,  “

”

is displayed.

Either turn the 

4

/

¢

knob 

!5

or

press the 

5

or 

∞

button 

c

to select “

”.

Press the 

4

/

¢

knob 

!5

or

button 

b

to turn off the timer program.

• To turn a timer program back on again, repeat

this procedure and select “

”.

7 Sleep timer

• The sleep timer function allows the unit to be in

standby mode automatically after specific period
of time.

Press the 

button 

⁄7

on the remote

control.

Each press of the button will increase the time
before shut down in the following sequence.

The sleep timer will be shown for 5 seconds in
the display, and it will count down until the time
has elapsed. When the programed sleep timer
has elapsed, the unit will automatically turn off. 

Note that the display will be dimmed when the
sleep timer is programed.

Press the 

button 

⁄7

. The display shows

the remaining time until standby mode begins.

To cancel the sleep timer, press the 

button 

⁄7

repeatedly until the display shows

“

”.

• When the sleep timer is programed, DIMMER

function does not activate.

10

20

30

60

90

120

OFF

• This unit is equipped with a last function memory

which stores the input and output setting
conditions as they were immediately before the
power is switched off.
This function eliminates the need to perform
complicated resettings when the power is turned
on.

• The unit is also equipped with a back-up

memory.
This function provides approximately one week
of memory storage when the main unit’s power
switch is off and with the mains cord
disconnected.

• When the indication of the display is not normal

or when the operation of the unit does not shows
the reasonable result, the initialization of the
microprocessor is required by the following
procedure.

Unplug the mains cord from the power outlet
after pressing the 

switch 

q

or button 

z

and setting the

standby mode.

Holding both the 

button 

u

and 

switch 

q

, plug the mains cord

into the power outlet.

Check that the entire display is flashing with an
interval of about 1 second, and release your
fingers from the 2 buttons and the
microprocessor will be initialized.

• If step 3 does not work,start over from step 1.

• If the microprocessor has been initialized all the

button settings are reset to the default values
(the values set upon shipment from the factory).

STANDBY

STANDBY

PHONES

PHONES

POWER ON / STANDBY

POWER ON / STANDBY

CD  RECEIVER  CR601

CD  RECEIVER  CR601

PUSH  TO  ENTER

PUSH  TO  ENTER

VOLUME

VOLUME

TREBLE

TREBLE

BASS

BASS

INPUT

INPUT

MENU

MENU

DIRECT

DIRECT

q

!5

u

⁄7

x

z

n

b

c

CR601N_01 Eng  05.10.21  1:22 PM  ページ26