Sony PCM-R700 사용자 설명서
3-859-278-11(1)
Writing Sub Codes
20
EN
START ID WRITE
START ID AUTO
DATA
AUTO
MIN
MAX
OFF
WIRED
WIRELESS
REMOTE
POWER
Ø
ON
ø
OFF
PHONE LEVEL
PHONES
•
•
•
•
•
•
•
•
•
•
•
RENUMBER
REHEARSAL
REHEARSAL
WRITE
WRITE
ERASE
ERASE
REPEAT
SKIP PLAY
LOCATE
MODE
COUNTER RESET
MARGIN RESET
PREVIOUS
AMS
=
OPEN/CLOSE
6
NEXT
+
STOP
p
REW
0
PLAY
(
FF
)
PAUSE
P
REC MUTE
R
REC
r
MENU
DATA
SHUTTLE
CH-1(L)
r
SET
MARK
0
10
ANALOG
DIGITAL
INPUT
REC LEVEL
•
•
•
•
•
•
•
•
•
•
•
OFF
ON
SBM
UNBALANCE
BALANCE
ANALOG INPUT
STANDARD
48k
44.1k
LONG
REC MODE
CH-2(R)
0
10
•
•
•
•
•
•
•
•
•
•
•
START ID
SKIP ID
OPEN/
CLOSE
COUNTER
REPEAT
1
3
2
RESET
MODE
6
CLEAR
4
6
5
7
9
8
0
CLEAR
Writing Start IDs During
Recording
Recording
Writing program numbers during recording
Program numbers occupy the same positions as the
start IDs and are determined by depending on the
following conditions:
start IDs and are determined by depending on the
following conditions:
When a program number is displayed
The next program number rises by one above when the next
start ID is written.
start ID is written.
When no program number is displayed (“--” appears
instead)
instead)
Program numbers are not written even when start IDs are
written. To write program nunbers, rewind the tape to the
nearest start ID to display the program number, and then
locate the position where you want to start recording.
written. To write program nunbers, rewind the tape to the
nearest start ID to display the program number, and then
locate the position where you want to start recording.
Specifying the first program number to be
assigned
1
assigned
1
Pause recording.
2
Press the number button(s) on the supplied
remote, or turn DATA to input the first program
number.
The number appears in the display.
To cancel the number, press the CLEAR button on
the supplied remote.
remote, or turn DATA to input the first program
number.
The number appears in the display.
To cancel the number, press the CLEAR button on
the supplied remote.
3
Start recording.
A start ID and the assigned program number are
written simultaneously.
A start ID and the assigned program number are
written simultaneously.
Note
During automatic start ID writing the positioning of some
start IDs may be inaccurately or inappropriately positioned
away from the beginning of the track. If this happens, you
can reposition or erase the start IDs later (see “Accurate
positioning of sub codes” on pages 21and 22, and “Erasing
Sub Codes” on page 23).
start IDs may be inaccurately or inappropriately positioned
away from the beginning of the track. If this happens, you
can reposition or erase the start IDs later (see “Accurate
positioning of sub codes” on pages 21and 22, and “Erasing
Sub Codes” on page 23).
Writing start IDs manually during recording
Press START ID WRITE.
“ID WRITE” appears in the display for a few seconds
and the start ID is written on the tape. “START ID”
flashes in the display during this time.
“ID WRITE” appears in the display for a few seconds
and the start ID is written on the tape. “START ID”
flashes in the display during this time.
I D W R I T E
START ID
Note
The interval between start IDs must be more than 18 seconds
(36 seconds in long-play mode). If the interval is less than 18
seconds (or 36 seconds), the deck may fail to detect the
second start ID while playing a tape.
(36 seconds in long-play mode). If the interval is less than 18
seconds (or 36 seconds), the deck may fail to detect the
second start ID while playing a tape.
Writing start IDs automatically during
recording
recording
Press START ID AUTO repeatedly until “AUTO”
appears in the display.
appears in the display.
For details on the condition for the automatic writing
of start IDs, see “Writing start IDs automatically during
recording” on page 7, and “Menu Operations” on
pages 24 and 25.
of start IDs, see “Writing start IDs automatically during
recording” on page 7, and “Menu Operations” on
pages 24 and 25.
Number buttons