Yamaha RX-V561 사용자 설명서
25
En
Optimizing the speaker setting for your listening room
English
PRE
P
ARA
T
ION
4
Make sure that “SETUP” is set to “AUTO”
and the pointer is pointing at “START”.
and the pointer is pointing at “START”.
y
You can also select the following setup methods. In this
You can also select the following setup methods. In this
case, press
Gk to select “SETUP”, press Gl / h to
select the one of the following choises and then select
“START”.
“START”.
Choices: AUTO, RELOAD, UNDO, DEFAULT
• Select “AUTO” to automatically run the entire
• Select “AUTO” to automatically run the entire
“AUTO SETUP” procedure.
• Select “RELOAD” to reload the last “AUTO
SETUP” settings and override the previous
settings.
settings.
• Select “UNDO” to undo the last “AUTO SETUP”
settings and restore the previous settings.
• Select “DEFAULT” to reset the “AUTO SETUP”
parameters to the initial factory settings.
“RELOAD” or “UNDO” is available only when you have
previously run “AUTO SETUP” and confirmed the results.
previously run “AUTO SETUP” and confirmed the results.
5
Press D
AMP and then press GENTER to
start the setup procedure.
This unit starts the auto setup procedure. Loud test
tones are output from each speaker during the auto
setup procedure. Once all items are set, the
“AUTO:RESULT” display appears in the OSD.
This unit starts the auto setup procedure. Loud test
tones are output from each speaker during the auto
setup procedure. Once all items are set, the
“AUTO:RESULT” display appears in the OSD.
• During the auto setup procedure, do not perform any
operation on this unit.
• We recommend getting out of the room while this unit is in
the auto setup procedure. It takes approximately 3 minutes
for this unit to complete the auto setup procedure.
for this unit to complete the auto setup procedure.
This unit performs the following checks:
Speaker wiring/volume level
WIRING/LEVEL
Checks which speakers are connected and the
polarity of each speaker. Also checks and adjusts the
volume level of each speaker.
polarity of each speaker. Also checks and adjusts the
volume level of each speaker.
Speaker distance
DISTANCE
Checks the distance of each speaker from the
listening position and adjusts the timing of each
channel.
listening position and adjusts the timing of each
channel.
Speaker size
SIZE
Checks the frequency response of each speaker and
sets the appropriate low-frequency crossover for each
channel.
sets the appropriate low-frequency crossover for each
channel.
The display changes as follows.
The results displayed under “RESULT” are as follows.
Number of speakers
SP
Displays the number of speakers connected to this unit in
the following order:
Front/Back/Subwoofer
the following order:
Front/Back/Subwoofer
Speaker distance
DIST
Displays the speaker distance from the listening position
in the following order:
Closest speaker distance/Farthest speaker distance
in the following order:
Closest speaker distance/Farthest speaker distance
Speaker level
LVL
Displays the speaker output level in the following order:
Lowest speaker output level/Highest speaker output level
Lowest speaker output level/Highest speaker output level
• If “E-6:INTERNAL ERROR” appears during the testing
procedure, restart from step 4.
• If you selected “RELOAD” in step 4, no test tones are output.
• If an error occurs during the “AUTO:CHECK” procedure, the
• If an error occurs during the “AUTO:CHECK” procedure, the
setup procedure is canceled and an error screen appears. For
details, see “If an error screen appears” on page 27.
details, see “If an error screen appears” on page 27.
• When this unit detects potential problems during the “AUTO
SETUP” procedure, “WARNING” and the number of warning
messages appears in the above of “RESULT” (see page 27).
messages appears in the above of “RESULT” (see page 27).
Note
Notes
Notes
AUTO:MENU
SETUP
;;;;;;;AUTO
. START
Automatic
processing
of all item
[ ]/[ ]:Up/Down
[ENTER]:Start
processing
of all item
[ ]/[ ]:Up/Down
[ENTER]:Start
p
p
AUTO:RESULT
NO WARNING
RESULT
RESULT
SP
:
3/2/0.1
DIST:
3.2/3.5m
LVL :
-2/+2dB
. SET
CANCEL
[ ]/[ ]:Up/Down
[ENTER]:Enter
[ENTER]:Enter
>
INITIALIZING
. WIRING/LEVEL
DISTANCE
SIZE
SIZE
WAITING
;;;
;;;;;;;;;;
[]:Exit
[
AUTO:CHECK