Yamaha RX-V2400 사용자 설명서
64
REMOTE CONTROL FEATURES
■
Macro operations
1
Set MACRO ON/OFF to ON.
2
Press a macro button.
• When you have finished using the Macro feature, set MACRO
ON/OFF to OFF.
• While the remote is carrying out a macro program, it will not
accept any other button’s function until the macro operation is
complete (the TRANSMIT indicator stops flashing).
complete (the TRANSMIT indicator stops flashing).
• Continue to aim the remote control at the component the macro
is operating until the macro operation is complete.
■
Programing a macro
You can program your own macros and use the Macro
feature to transmit several remote control commands in
order by pressing a single button. Be sure to set up
manufacturer codes or perform learning operations before
programming the macro. We do not recommend
programming continuous operations such as volume
control in a macro.
feature to transmit several remote control commands in
order by pressing a single button. Be sure to set up
manufacturer codes or perform learning operations before
programming the macro. We do not recommend
programming continuous operations such as volume
control in a macro.
• The default macro is not cleared when a new macro is
programmed for a button. The default macro can be used again
when the programmed macro is cleared.
when the programmed macro is cleared.
• It is not possible to add a new signal (macro step) to the default
macro. Programming a macro changes all macro contents.
1
Press MACRO using a ballpoint pen or
similar object.
similar object.
“MCR ?” appears in the display window.
y
Complete each of the following steps in 30 seconds.
Otherwise, the learning mode will be automatically
cancelled. In this case, press MACRO again.
Otherwise, the learning mode will be automatically
cancelled. In this case, press MACRO again.
2
Press the macro button you will use to
operate the macro.
operate the macro.
The macro button name and the selected component
name appear alternately in the display window.
name appear alternately in the display window.
• “AGAIN” appears in the display window if you press a button
other than a macro button.
• To change the selected source component, press SOURCE
SELECT k/n. Pressing the input selector buttons will program
a macro step, whereas SOURCE SELECT k/n only changes
the selected component and corresponding component control
area.
a macro step, whereas SOURCE SELECT k/n only changes
the selected component and corresponding component control
area.
3
Press the buttons for the functions you want
to include in the macro operation in order.
to include in the macro operation in order.
You can set up to 10 steps (10 functions). After you
have set 10 steps, “FULL” appears and the remote
control automatically exits from the macro mode.
have set 10 steps, “FULL” appears and the remote
control automatically exits from the macro mode.
“NG” appears in the display window if programming was
unsuccessful. In this case, start over from step 2.
unsuccessful. In this case, start over from step 2.
4
Press MACRO again when the operation
sequence you want to program is complete.
sequence you want to program is complete.
Note
Notes
TRANSMIT
RE-NAME
STANDBY
SYSTEM
CLEAR
LEARN
MACRO
OFF
ON
MACRO
PHONO
MULTI CH IN
CD
DVD
DVR/VCR2
VCR 1
DTV
CBL/SAT
CD-R
MD/TAPE
TUNER
V-AUX
POWER
TV
POWER
MACRO
MACRO ON/OFF
Macro buttons
MACRO
Notes
Note
PHONO
CD
DVD
DVR/VCR2
VCR 1
DTV
CBL/SAT
CD-R
MD/TAPE
TUNER
V-AUX
INPUT MODE
SOUND
PHONO
CD
DVD
DVR/VCR2
VCR 1
TITLE
MENU
CHAPTER
PAUSE
STOP
POWER
REC
SELECT
DISPLAY
SEARCH
SOURCE
PLAY
–
+
ENTER
DTV
CBL/SAT
CD-R
MD/TAPE
TUNER
V-AUX
1
2
MCR 1: DVD
a
MCR 2: DVD
h
indicate the number
of macro steps you
entered
of macro steps you
entered
appear alternately so that you
can set up the next step
can set up the next step
00_RX-V2400U_EN.book Page 64 Friday, October 10, 2003 10:54 AM