JVC RX-889PGD 사용자 설명서
23
English
IMPORTANT:
When using the remote control, check to see if its
remote control mode selector is set to the correct
position:
To operate this receiver, set it to “AUDIO/TV/
VCR” (except when selecting the DBS tuner as
the source).
remote control mode selector is set to the correct
position:
To operate this receiver, set it to “AUDIO/TV/
VCR” (except when selecting the DBS tuner as
the source).
Adjusting the 3D-PHONIC Modes
Once you have adjusted the 3D-PHONIC modes, the adjustment is
memorized for each 3D-PHONIC mode.
memorized for each 3D-PHONIC mode.
Before you start, remember...
• Make sure that you have set the speaker information correctly
• Make sure that you have set the speaker information correctly
(see page 14).
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel:
1. Press DSP MODE repeatedly until
“3D ACTION (or 3D DIGITAL)”
or “3D THEATER” appears on
the display.
or “3D THEATER” appears on
the display.
The 3D-PHONIC, DSP, PRO LOGIC and selected 3D-PHONIC
mode indicators also light up on the display.
mode indicators also light up on the display.
2. Adjust the effect level.
1) Press BALANCE/SURROUND
ADJUST repeatedly until “DSP
EFFECT” appears on the display.
The display changes to show the current
setting.
EFFECT” appears on the display.
The display changes to show the current
setting.
2) Turn MULTI JOG to select the effect
level.
• As you turn it, the effect level changes
• As you turn it, the effect level changes
as follows:
As the number increases, the selected 3D-PHONIC mode
becomes stronger.
becomes stronger.
From the remote control:
1. Press SURROUND MODE
repeatedly until “3D ACTION (or
3D DIGITAL)” or “3D
THEATER” appears on the
display.
3D DIGITAL)” or “3D
THEATER” appears on the
display.
The 3D-PHONIC, DSP, PRO LOGIC and selected 3D-PHONIC
mode indicators also light up on the display.
mode indicators also light up on the display.
2. Press SOUND.
The 10 keys are activated for sound adjustments.
AUDIO/
TV/VCR
TV/VCR
CATV/DBS
DSP MODE
BALANCE/
SURROUND
ADJUST
3. Press EFFECT to select an effect
level you want.
• Each time you press the button, the effect
level changes as follows:
As the number increases, the selected 3D-PHONIC mode
becomes stronger.
becomes stronger.
Adjusting the DAP Modes
Once you have adjusted the DAP modes, the adjustment is
memorized for each DAP mode.
memorized for each DAP mode.
Before you start, remember...
• Make sure that you have set the speaker information correctly
• Make sure that you have set the speaker information correctly
(see page 14).
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
• You cannot adjust the rear speaker output level when you have set
“REAR SPK” to “NONE.” See page 14.
• When the DAP mode is used with the SEA mode (see page 19),
sounds may be distorted. If this happens, turn off the SEA mode.
On the front panel:
1. Press DSP MODE repeatedly until
the DAP mode — LIVE CLUB,
DANCE CLUB, HALL, or
PAVILION — appears on the
display.
DANCE CLUB, HALL, or
PAVILION — appears on the
display.
The DSP and the selected DAP mode indicators also light up on
the display.
• When you have set “REAR SPK” to “NONE,” the 3D-
the display.
• When you have set “REAR SPK” to “NONE,” the 3D-
PHONIC indicator also lights up.
2. Adjust the speaker output levels.
1) Press BALANCE/SURROUND
ADJUST repeatedly until one of the
indications appears on the display.
“REAR L LEVEL”:
indications appears on the display.
“REAR L LEVEL”:
To adjust the left rear speaker level.
“REAR R LEVEL”:
To adjust the right rear speaker level.
2) Turn MULTI JOG to adjust the
selected speaker output level (from –10
dB to +10 dB).
dB to +10 dB).
3) Repeat 1) and 2) to adjust the other
speaker output level.
DSP EFFECT 1
DSP EFFECT 2
DSP EFFECT 3
DSP EFFECT 4
DSP EFFECT 5
EFFECT
7
/P
DSP EFFECT 1
DSP EFFECT 2
DSP EFFECT 3
DSP EFFECT 4
DSP EFFECT 5
MULTI JOG
BALANCE/
SURROUND
ADJUST
MULTI JOG
SURROUND
MODE
SOUND
DSP MODE
EN19_30.RX-889P[US, UB]/f
99.4.12, 5:32 PM
23