ONKYO TX-SR702/702E 사용자 설명서
45
First Time Setup
—Continued
TV Format Setup (not American models)
Here you can specify the TV format used in your area.
Note:
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
and [ENTER] button.
AM Frequency Step Setup
(some models only)
Here you can specify the AM frequency step used in
your area. When this setting is changed, all radio presets
are deleted.
your area. When this setting is changed, all radio presets
are deleted.
Note:
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
and [ENTER] button.
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [
]/[
]
buttons to select “1. Initial
Setup,” and then press [ENTER].
Setup,” and then press [ENTER].
The Initial Setup menu appears.
3
Use the Up and Down [
]/[
]
buttons to select “3. Hardware
Setup,” and then press [ENTER].
Setup,” and then press [ENTER].
The Hardware Setup menu appears.
(Menus vary depending on country.)
4
Use the Up and Down [
]/[
]
buttons to select “c. TV Format,”
and then use the Left and Right
[
and then use the Left and Right
[
]/[
] buttons to select:
Auto:
Conforms with the video
input signal.
input signal.
PAL:
Select if the TV system in
your area is PAL.
your area is PAL.
NTSC:
Select if the TV system in
your area is NTSC.
your area is NTSC.
5
Press the [SETUP] button.
The setup menu closes.
RECEIVER
ENTER
ENTER
Menu
------------------------
1.Initial Setup
2.Speaker Setup
2.Speaker Setup
Advanced Setup
3.Surround Setup
4.Audio Adjust
5.Listening Mode Preset
6.Preference
3.Surround Setup
4.Audio Adjust
5.Listening Mode Preset
6.Preference
Basic Setup
1.Initial Setup
------------------------
2.Component Video
3.Hardware Setup
3.Hardware Setup
1.Digital Input
1-3.Hardware Setup
------------------------
:Not Activated
b.Sp Impedance Minimum
:6ohms
c.TV Format :NTSC
b.Sp Impedance Minimum
:6ohms
c.TV Format :NTSC
d.AM Frequency Step
: 9kHz
: 9kHz
a.Powered Zone2
ENTER
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [
]/[
]
buttons to select “1. initial
Setup,” and then press [ENTER].
Setup,” and then press [ENTER].
The Initial Setup menu appears.
3
Use the Up and Down [
]/[
]
buttons to select “3. Hardware
Setup,” and then press [ENTER].
Setup,” and then press [ENTER].
The Hardware Setup menu appears.
4
Use the Up and Down [
]/[
]
buttons to select “d. AM Fre-
quency Step,” and then use the
Left and Right [
quency Step,” and then use the
Left and Right [
]/[
] buttons to
select:
10 kHz:
Select if 10 kHz steps are
used in your area.
used in your area.
9 kHz:
Select if 9 kHz steps are used
in your area.
in your area.
5
Press the [SETUP] button.
The setup menu closes.
RECEIVER
ENTER
ENTER
Menu
------------------------
1.Initial Setup
2.Speaker Setup
2.Speaker Setup
Advanced Setup
3.Surround Setup
4.Audio Adjust
5.Listening Mode Preset
6.Preference
3.Surround Setup
4.Audio Adjust
5.Listening Mode Preset
6.Preference
Basic Setup
1.Initial Setup
------------------------
2.Component Video
3.Hardware Setup
3.Hardware Setup
1.Digital Input
1-3.Hardware Setup
------------------------
:Not Activated
b.Sp Impedance Minimum
:6ohms
c.TV Format :NTSC
b.Sp Impedance Minimum
:6ohms
c.TV Format :NTSC
d.AM Frequency Step
: 9kHz
: 9kHz
a.Powered Zone2
ENTER
TX-NR702,602_En.book Page 45 Monday, July 26, 2004 11:05 AM