ONKYO TX-L55 사용자 설명서
31
Basic Setup
—Continued
Notes:
• This procedure can also be performed by using the
[SETUP] button. Press the REMOTE MODE [AMP]
button followed by the [SETUP] button. Use the Up
and Down [
button followed by the [SETUP] button. Use the Up
and Down [
]/[
] buttons to select “Level Cal,” and
then press [ENTER]. Use the Left and Right [
]/[
]
buttons to adjust the speaker volume, and use the
Down [
Down [
] button to select the next speaker. Unlike the
above procedure, the next speaker will not be selected
automatically after two seconds.
automatically after two seconds.
Digital Audio Input Setup
To enjoy Dolby Digital and DTS, you must connect your
DVD player to the TX-L55 by using a digital audio con-
nection (coaxial or optical).
This section explains how to change the digital audio
input socket to input source assignments. You only need
to change them if your connections don’t match the
defaults listed in the following table.
DVD player to the TX-L55 by using a digital audio con-
nection (coaxial or optical).
This section explains how to change the digital audio
input socket to input source assignments. You only need
to change them if your connections don’t match the
defaults listed in the following table.
For example, if you connect your DVD player to the
OPT 1 DIGITAL INPUT, you’ll need to change the
DVD input source from COAX to OPT 1.
OPT 1 DIGITAL INPUT, you’ll need to change the
DVD input source from COAX to OPT 1.
If you want to use the TV input source with only the
analog TV IN, change the TV input source assignment
from OPT1 to “----” (Analog).
You can change the assignments as follows.
analog TV IN, change the TV input source assignment
from OPT1 to “----” (Analog).
You can change the assignments as follows.
3
Use the [CH SEL] button to select
the speakers, and use the
[LEVEL+] and [LEVEL–] buttons
to adjust the volume.
the speakers, and use the
[LEVEL+] and [LEVEL–] buttons
to adjust the volume.
The level can be adjusted from –12 to
+12 dB in 1 dB steps.
+12 dB in 1 dB steps.
If you don’t press anything for two sec-
onds, the next speaker will be selected
automatically.
onds, the next speaker will be selected
automatically.
4
Repeat step 3 until the volume of
the test tone coming from each
speaker is the same.
the test tone coming from each
speaker is the same.
Speakers that you set to No or Non in
the Speaker Configuration (page 48) do
not output the test tone.
the Speaker Configuration (page 48) do
not output the test tone.
5
Press the [TEST TONE] button.
The setup menu closes.
Don’t forget to turn down the volume if
you turned it up while setting the levels.
Don’t forget to turn down the volume if
you turned it up while setting the levels.
Assigning Inputs to Input Sources
Input source
Default digital input assignment
DVD
COAX
TV
OPT1
VIDEO1
OPT2
VIDEO2
- - - - (Analog)
AUX
- - - - (Analog)
LEVEL LEVEL
+
-
CH SEL
TEST TONE
1
Press the REMOTE MODE [AMP]
button followed by the [INPUT
SELECTOR] button for the input
source whose assignment you
want to change.
button followed by the [INPUT
SELECTOR] button for the input
source whose assignment you
want to change.
There is no assignment for the TUNER
input source.
input source.
2
Press the [SETUP] button.
3
Use the Up and Down [
]/[
]
buttons to select “Input Set,” and
then press [ENTER].
then press [ENTER].
4
Use the Up and Down [
]/[
]
buttons to select “Digital In,” and
then use the Left and Right [
then use the Left and Right [
]/
[
] buttons to select:
COAX:
Select if the component is
connected to the COAX DIG-
ITAL INPUT.
ITAL INPUT.
OPT1:
Select if the component is
connected to the OPT1 DIGI-
TAL INPUT.
TAL INPUT.
OPT2:
Select if the component is
connected to the OPT2 DIGI-
TAL INPUT.
connected to the OPT2 DIGI-
TAL INPUT.
5
Press the [SETUP] button.
The setup menu closes.
AMP
TUNER
TV
AUX
TUN
DVD
V1
INPUT SELECTOR
V2
ENTER
ENTER
ENTER
TX-L55_En.book Page 31 Tuesday, June 1, 2004 9:02 AM