Marantz SR6001 사용자 설명서

⁄3 CONTROL 

These buttons are used when operating PLAY, STOP, 
PAUSE and other commands of a source.

T.DISP button
Used to select the display mode in RDS.

PTY button
Used to display the programme type information of 
the current station.

F.DIRECT button
Used to select the "Frequency direct input".

PRESET +/- buttons
Used to select a preset station up and down.

TUNING +/- buttons
Used to tune a frequency station up and down.

⁄4 ANGLE/V-OFF 

(When AMP mode is selected)
Used to turn off the video signal.

⁄5  DISC+/CH. SEL button

(When AMP mode is selected)
Used to call up SETUP MAIN MENU and adjust 
speaker levels or 7.1 ch input level.

⁄6  BASS +/- buttons

These buttons are used to adjust the tone control 
of low frequency sound for left, right and subwoofer 
speaker.

⁄7 SEND 

Indicates when the remote controller is transmitting 
a signal.

⁄8 

(When AMP mode is selected)
These buttons are used to turn the SR6001 on or 
off.

⁄9 SURROUND 

This button is used to selects the surround mode.

¤0 P.DIRECT 

When this button is pressed, the tone control circuit 
is bypassed.

¤1  BAND/LIP SYNC/INPUT button

(When TUNER mode is selected)
Used to select a radio band.

(When AMP mode is selected)
Used to select LIP SYNC mode.

(When TV mode is selected)
Used to select monitor input.

¤2 T.MODE 

(When TUNER mode is selected)
Used to select auto stereo mode or mono mode 
when the FM band is selected.
The “AUTO” indicator lights in the auto stereo mode.

¤3 P.SCAN 

(When TUNER mode is selected)
Used to start preset scan.

¤4 MEMO/HT-EQ 

This button is used to store setting to memory or 
program a source.

(When AMP mode is selected)
Used to turn on or off HT(Home Theater)-EQ mode. 
This mode compensates for the audio portion of a 
movie sounding “bright”.

¤5 MUTE 

This button is used to mute the audio for the amplifi er 
and television.

Set the AMP mode to use this button with the 
SR6001.

¤6 VOLUME 

This button is used to adjust the volume for the 
amplifi er and television.

Set the AMP mode to use this button with the 
SR6001.

¤7 M-SPKR 

(When AMP mode is selected)
Used to turn on and off multi speaker.

¤8 MENU 

(When AMP mode is selected)
This button is used to call up the SETUP MAIN 
MENU of the SR6001.

¤9 

1, 2, 3, 4 (CURSOR) / ENTER 
buttons

These buttons are used when controlling the cursor 
of the SR6001, DVD or other AV equipment.

‹0 EXIT 

(When AMP mode is selected)
This button is used to cancel setting in the setup 
menu.

‹1 SUBTITLE/ATT. 

(When AMP mode is selected)
When the input signal is too high and the voice 
distorts even by throttling the SR6001 VOLUME 
control, turn on this function.
“ATT” is indicated when this function is activated.
The input level reduced. Attenuator is invalid for the 
output signal of “REC OUT”.

This function is unavailable while the digital input is 
selected.

‹2 AUDIO 

(When DVD mode is selected)
Used to select one of the audio language.

‹3  TREBLE +/- buttons

These buttons are used to adjust the tone control of 
high frequency sound for left and right speaker.

‹4 SOURCE 

These buttons are used to switch the source of your 
A/V Receiver / amplifer. Each time a source button is 
pressed, the remote control changes to the source 
which was pressed.
This remote control can control 12 types of equipment. 
To change the A/V Receiver / amplifi er source, press 
this button twice within two seconds. The signal is 
sent when it is pressed the second time.

Select the AMP as the source to use this remote 
controll with the SR6001.

‹5  Infrared Transmitter and Learning 

This transmitter emits infrared light. Press the 
buttons while pointing the transmitter towards the 
infrared receiver window of the SR6001 or other 
AV equipment. Be sure to also point towards other 
remote controls when using the learning function.

SR6001U DFU_1_ENG 1_4.indd   10

SR6001U DFU_1_ENG 1_4.indd   10

06.12.21   4:13:58 PM

06.12.21   4:13:58 PM