Marantz SR6001 사용자 설명서

 

  Press and hold down the SOURCE button 

for appliance which should be controlled and 
press  SET button until the SEND indicator 
blinking twice.

 

  Then back light fl ushes.

 

  Press the below codes to reset.

  TV : 

1000

  DVD 

: 

2000

  VCR 

: 

3000

  DSS 

: 

4000

 

  The indicator will blink twice.

After this procedure, the selected SOURCE button is 
set initial code.

 

  Press and hold down the SOURCE button for 

appliance which should be controlled and press 
SET button until the SEND indicator blinking 
twice. Then back light fl ushes.

 

  Aim the remote control at the appliance and 

slowly alternate between pressing CH+ button 
and the SOURCE ON/OFF button for the 
appliance.

 

  Stop when the appliance turns off.

 

 Press 

ENTER button once to lock in the code.

 

  Press and hold down the SOURCE button for 

appliance which should be controlled and press 
SET button until the SEND indicator blinking twice 
then back light fl ushes.

 

 Press 

the 

INFO button.

 

  The SEND indicator will blink twice.

 

  To view the code for fi rst digit, press 1 once.

 

  Wait 3 seconds, count the SEND indicator 

blinks (e.g. 3 blinks = 3) and write down the 
number.

If a code digit is “0”, the SEND indicator will not 
blink.

 

 Repeat 

step 

 three more times for remaining 

digits. Use 2 for the second digit, 3 for the third 
digit, and

 4 for the fourth digit.

•  Some codes may be not match your equipment.
  In this case, you can use LEARN mode to store these 

codes.

•  The preset codes do not cover full functions.
  If you need extra function, use LEARN mode to 

store extra function.

• Wen the batteries are getting weak, the preset 

procedure is not successful.

 

  Press and hold down the SOURCE button for the 

appliance which should be controlled and press 
SET button until the SEND indicator blinks twice. 
Then back light fl ushes.

 

  Press the 4-digit code for appliance (code table 

at the end of this book)

 

  When the procedure is successful, the SEND 

indicator will blink twice.

If the indicator did not blink twice, then repeat steps 1 
through 2 and try entering the same code again.

 

  Switch on the appliance which should be 

controlled.

(When operating Marantz AV equipment products)
This remote control is preset with a total of 12 types 
of remote codes, including Marantz TV (television), 
DVD, VCR (VCR deck), DSS (satellite broadcasting 
tuner), TUNER, CD, CD-R, MD, TAPE (tape deck), 
AUX1, AUX2, and AMP (amplifi er).
Learning is not necessary for Marantz products. You 
can use these products without setting any codes.

 

 Press 

the 

SOURCE button.

For this example, press DVD. 
Pressing the SOURCE button once changes 
the remote control to the settings for the source 
that was pressed. 
To change the amplifi er on other source, press 
the  SOURCE button twice (double-click). The 
code is sent, and then the amplifi er source 
changes to DVD.

Each time press the buttons, illuminate button 2 
seconds.
To turn off back light, press and hold down the SET 
and OFF button until SEND indicator blinks twice.
To turn on it again, press and hold down the SET and 
ON button until SEND indicator blinks twice.
Initial is back light ON.

(When operating non-Marantz AV equipment 
products)
This remote control is preset with remote control 
codes from AV equipment by other manufacturers. 
The preset codes are TV, VCR, DVD and DSS. 
Settings can be made in one of two ways.
When the preset codes are set, the following codes 
are contained in the source button of the remote 
control.

See the attached manufacturer number list for the 
preset manufacturers, devices, preset numbers, and 
other settings.

Remote control 
source name

Corresponding preset 
code

Device name

TV

TV

Television

DVD

DVD

DVD player

VCR

VCR

Video deck

DSS

SATELLITE

Satellite broadcasting 
tuner equipment

SR6001U DFU_1_ENG 1_4.indd   15

SR6001U DFU_1_ENG 1_4.indd   15

06.12.21   4:14:00 PM

06.12.21   4:14:00 PM