Marantz SR6001 사용자 설명서
ENGLISH
21
DC OUT
OUTPUT
IN
OUT
PRE
OUT
OUT
SL
L
R
SR
FLASHER
IN
OUT
L
OUTPUT
E
CD/CD-R
OUT
OUT
MULTI
R
(AUX2)
O
7.1CH
IN
T
UT 1(TV)
INPUT 4(DSS)
N
SR
IN
UT 3(VCR)
SL
CB
/
PB
CR
/
PR
CR
/
PR
CR
/
PR
CB
/
PB
CB
/
PB
Y
Y
DVD(2)
DSS(4)
VCR(3)
TV(1)
MONI. OUT
SBR
SBL
SBR
SBL
C
SW
SW
C
AC
INPUT 2(DVD)
S-VIDEO
MODEL NO
XM
L
R
FRONT
SURR.
SURR.
BACK
SUB
WOOFER
CENTER
L
R
FRONT
SURR.
SURR.
BACK
SUB
WOOFER
CENTER
R
L
R
L
R
L
L
R
R L
L
R
L
R
R L
R L
R L
R L
R L
ADVANCED CONNECTING
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel audio
source such as a Super Audio CD multichannel
player, DVD audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the SETUP
MAIN MENU. See page 29.
source such as a Super Audio CD multichannel
player, DVD audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the SETUP
MAIN MENU. See page 29.
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PREOUT jacks are for connecting external
power amplifi ers.
Be sure to connect each speaker to the corresponding
external power amplifi er.
power amplifi ers.
Be sure to connect each speaker to the corresponding
external power amplifi er.
Power
Amplifer
DVD Audio player
or
Super Audio CD
Multi channel player
Center
Front
Left
Left
Front
Right
Right
Surround
Left
Left
Surround
Right
Subwoofer
Surround
Back Left
Back Left
FM (75)
GND
AM
DC OUT
OUTPUT
COMPONENT
VIDEO
IN
OUT
SL
L
R
SR
FLASHER
IN
INPUT 1(DVD)
COAX.
DIGITAL IN
DIGITAL OUT
3
5
4
2
1
OUT
R
OUT
L
OUTPUT
TAPE
CD/CD-R
OUT
OUT
IN
MULTI
R
L
DSS
(AUX2)
AUDIO
TV
IN
OPT.
DVD(2)
DSS(4)
TV(1)
VIDEO
OUT
VCR(3)
OUT
IN
RC-5
MULTI RC
INPUT 1(TV)
INPUT 4(DSS)
IN
SR
VCR
IN
INPUT 3(VCR)
DVD
SL
INPUT 2(DSS)
ANTENNA
CB
/
PB
CR
/
PR
CR
/
PR
CR
/
PR
CB
/
PB
CB
/
PB
Y
Y
Y
DVD(2)
DSS(4)
VCR(3)
TV(1)
MONI. OUT
MONITOR
OUT
SBR
SBL
SBR
SBL
S
S
INPUT 2(DVD)
S-VIDEO
HDMI
Ver1.2
Ver1.2
REMOTE
CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL
EXTERNAL INTERNAL
EXTERNAL INTERNAL
1
RC OUT
2
CONNECTING THE REMOTE CONTROL JACKS
DVD player
CD recorder
q
You can control other Marantz products through the
SR6001 with the remote control by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is
received by the remote sensor on the SR6001. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
control only at the SR6001. Also, if a Marantz power
amplifi er (some models excluded) is connected to
one of these terminals, the power amplifi er’s, power
switch is synchronized with this unit’s power switch.
You can control other Marantz products through the
SR6001 with the remote control by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is
received by the remote sensor on the SR6001. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
control only at the SR6001. Also, if a Marantz power
amplifi er (some models excluded) is connected to
one of these terminals, the power amplifi er’s, power
switch is synchronized with this unit’s power switch.
Set the REMOTE CONTROL SWITCH on the other
units, (not the SR6001) to “EXT.” (external) to use
this feature.
units, (not the SR6001) to “EXT.” (external) to use
this feature.
CD player
OPTION
w
Whenever external infrared sensors or similar devices
are connected to RC-5 IN of the SR6001, be sure to
always disable operation of the infrared sensor on the
main unit by using the following procedure.
Whenever external infrared sensors or similar devices
are connected to RC-5 IN of the SR6001, be sure to
always disable operation of the infrared sensor on the
main unit by using the following procedure.
1.
Hold down the MULTI button and the MENU
button on the front panel at the same time for
fi ve seconds.
fi ve seconds.
2.
The setting “IR=ENABLE” is shown on the FL
DISPLAY.
3.
Press
the
CURSOR buttons (
1, 2) to change
this to “IR=DISABLE”.
4.
Press
the
ENTER button. Once this setting is
made, the infrared sensor on the main unit is
disabled.
disabled.
Note:
• Be sure to set to “IR=ENABLE” when external
infrared sensors or similar devices are not connected.
Otherwise, the main unit will be unable to receive
remote control commands.
Otherwise, the main unit will be unable to receive
remote control commands.
5.
To restore the original setting, perform steps 1
to 4 to set to “IR=ENABLE”.
Surround
Back Right
Back Right
SR6001U DFU_1_ENG 1_4.indd 21
SR6001U DFU_1_ENG 1_4.indd 21
06.12.21 4:14:03 PM
06.12.21 4:14:03 PM