Marantz SR6001 사용자 설명서

SUB W: 

Set the distance from the subwoofer to your 
normal listening position.

SURR. B L: 

Set the distance from the surround back left 
speaker to your normal listening position.

SURR. B R: 

Set the distance from the surround back right 
speaker to your normal listening position.

•  Set the distance to each speaker in meters (m) or feet 

(ft) as follows.

  m: 0.03 - 9.15 m in 0.03 m steps

  ft: 0.1 - 30.0 ft in 0.1 ft steps

  (The values appearing on the FL display are 

approximate.)

•  For the speakers that you have selected “NONE” the 

speaker size menu will not appear.

• The setting for surr.back L and surr.back R appears 

if it is set, two surround back speakers in the 
SPEAKER SIZE menu.

• The setting of SURR. BACK appears if it is set for 

one surround back speaker in the SPEAKER SIZE 
menu.

 After you complete this portion of the setup,  

move the cursor to “NEXT” with the 

3, 4, 1 and 

2 cursor buttons and press the ENTER button 
to go to the next page.

        S P E A K E R   L E V E L
T E S T   M O D E     :    

M A N U A L

F R O N T   L         :       0 . 0 d B
C E N T E R           :       0 . 0 d B
F R O N T   R         :       0 . 0 d B
S U R R . R           :       0 . 0 d B
S U R R . B   R       :       0 . 0 d B
S U R R . B   L       :       0 . 0 d B
S U R R . L           :       0 . 0 d B
S U B   W             :       0 . 0 d B

R E T U R N     B A C K          

 

E X I T

Here you can set the volume for each speaker so that 
they are all heard by the listener at the same level. 
We recommend holding a dB SPL (Sound Pressure 
Level) meter at the listening position, at arms length, 
and pointing straight up at the ceiling, adjust the level 
of each speaker in turn unit it reads 75dB SPL when 
the meter is set to “C” weighting and Slow responce.

• The speaker level settings are not available in 7.1 

Channel Input mode, Pure Direct mode and Source 
Direct mode. 

TEST MODE:  

Select “MANUAL” or “AUTO” generation of the test 
tone with the 

1 or 2 cursor buttons. 

If you select “AUTO”, the test tone will be cycled 
through in a circular pattern beginning at Left  → 
Center  → Right → Surround Right → Surround 
Back Right → Surround Back Left → Surround 
Left → Subwoofer → Left, in 2 seconds increments 
for each channel.
Using the 

1 or 2 cursor buttons, adjust the volume 

level of the noise from the speaker so that it is the 
same level for all the speakers. 

If you select “MANUAL”, adjust the output level of 
each speaker as listed below.

 

 Move the cursor to FRONT L by pressing the 

4 cursor button. The SR6001 will emit a pink 
noise from the front left speaker. 

 

  Remember the level of this noise and then 

press the 

4 cursor button. 

 

  (Note that this can be adjusted to any level 

between -12 and +12 dB in 0.5 dB increments.) 

 

  The SR6001 will now emit the pink noise from 

the center speaker.

 Using the 

1 and 2 cursor buttons, adjust the 

volume level of the noise from the center 
speaker so that it is the same level as the front 
left speaker. 

 Press the 

4 cursor button again. The SR6001 

will now emit the pink noise from the front right 
speaker.

  Repeat steps 13 and 14 for the front right and 

other speakers until all speakers are adjusted 
to the same volume level.

After you complete this portion of the setup, press the 
ENTER button to move the cursor to “RETURN”. Press 
the ENTER button to go to “2. SPKR SETUP”.

• Speakers for which you selected “NONE” in the 

SPEAKER SIZE menu will not appear. 

• Surr. Back L and Surr. Back R appear if it is set for 

two surround back speakers in the SPEAKER SIZE 
menu. 

• Surr. Back appears if it is set for one surround back 

speaker in the SPEAKER SIZE menu.

• To adjust the speaker levels for 7.1 channel input 

sources, you will need to use the 7.1 Ch Input sub 
menu. (See page 37)

•  SUB W can be set from –18dB to +12dB.

SR6001U DFU_1_ENG 2_4.indd   36

SR6001U DFU_1_ENG 2_4.indd   36

06.12.21   4:14:33 PM

06.12.21   4:14:33 PM