Marantz SR6001 사용자 설명서

This function allows the name of each preset channel 
to be entered using alphanumeric characters. 
Before name inputting, you need to store preset 
stations with the preset memory operation.

AAC

 

  Recall the preset number to be inputted name 

with the method described in “Recalling” a 
preset station.

 

 Press 

the 

MEMORY button on the front panel 

or press the MEMO button on the remote for 
more than 3 seconds.

 

  The left most column of the station name 

indicator fl ashes, indicating the character entry 
ready status.

 

  When you press the 

3 or 4 cursor buttons on 

the front panel or the TUNING + or – buttons on 
the remote control unit, alphabetic and numeric 
characters will be displayed in the following 
order:

       A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → + 

→ / → (Blank) → A

→ 

→ DOWN

AAC

If you have stations memorized, and there is a gap in 
the sequential order:
I.e. the stations are stored as follows 

 1) 

87.1 

MHz

 2) 

93.1 

MHz

 

 3)  94.7 MHz

 10) 

105.9 

MHz

(notice there is no stations programmed for pre sets 
for 4-9), you can have pre set 10 become pre set 5: 
To sort the numbers, press and hold the MEMORY 
and the 

4 cursor buttons.

“PRESET SORT” will appear on the display and 
sorting will be done.

You can remove preset stations from the memory 
using the following procedure.

AAC

 

  Recall the preset number to be cleared with 

the method described in “Recalling” a preset 
station.

 

 Press 

the 

MEMORY button on the front panel 

or press the MEMO button on the remote.

 

  The stored preset number blinks in the display 

for 5 seconds. While blinking, press the CLEAR 
button on the front panel or press the CL button 
on the remote.

 

  “xx CLEAR” appears on the display to indicate 

that the specified preset number has been 
cleared.

•  To clear all stored preset stations, press and hold the 

CLEAR and the ENTER buttons for two seconds.

 

  After selecting the fi rst character to be entered, 

press the MEMORY or ENTER button, or press 
the MEMO button on the remote. 

      The entry in this column is fi xed and the next 

column starts to fl ash. Fill the next column the 
same way.

 

  To move back and forth between the characters, 

press the 

1 / 2 cursor buttons or press PRESET 

+ or – button on the remote.

• Unused columns should be filled by entering 

blanks.

 

  To save the name, press the MEMORY or 

ENTER button on the front panel, or press the 
MEMO button on the remote for more than 2 
seconds.

 

  Instead of using the 

3 and 4 cursor buttons 

or the TUNING + or – buttons of the remote 
controller unit to select characters, characters 
can be input from the numeric keys of the 
remote control unit. See the below table for 
a correspondence between characters and 
numeric keys.

Ten keypad

Press, press again, press again, etc.

1

A → B → C → 1 → A

2

D → E → F → 2 → D

3

G → H → I → 3 → G

4

J → K → L → 4 → J

5

M → N → O → 5 → M

6

P → Q → R → 6 → P

7

S → T → U → 7 → S

8

V → W → X → 8 → V

9

Y → Z → space → 9 → Y

0

– → + → / → 0

SR6001U DFU_1_ENG 3_4.indd   55

SR6001U DFU_1_ENG 3_4.indd   55

06.12.21   4:15:43 PM

06.12.21   4:15:43 PM