Russound CAV6.6 사용자 설명서
80
The configuration shows how the CAV6.6 distrib-
utes audio/video throughout the house using six
UNO System Keypads and six audio/video
source components.
utes audio/video throughout the house using six
UNO System Keypads and six audio/video
source components.
Source Components
The configuration allows for any zone to select
any one of the six source inputs.
The configuration allows for any zone to select
any one of the six source inputs.
Keypads
The configuration uses a single UNO-S2 Keypad
per zone. Each keypad is connected to the
CAV6.6’s Keypad Port using the RJ-45 T568A
wiring configuration. Each keypad port number
corresponds with the zone number. This gives
complete control of the zone to one keypad.
The configuration uses a single UNO-S2 Keypad
per zone. Each keypad is connected to the
CAV6.6’s Keypad Port using the RJ-45 T568A
wiring configuration. Each keypad port number
corresponds with the zone number. This gives
complete control of the zone to one keypad.
The UNO-S2 Keypad can control the source
equipment, volume for the zone, source selection,
tone control, mute, and other functions.
Programmable functions are also possible. The
IR receiver on the keypad also allows the
SRC2 and other remotes to control not only the
zone but also the source equipment.
equipment, volume for the zone, source selection,
tone control, mute, and other functions.
Programmable functions are also possible. The
IR receiver on the keypad also allows the
SRC2 and other remotes to control not only the
zone but also the source equipment.
IR Remote control through Keypad
To control the source components via IR from
the UNO-S2 Keypad, an IR emitter must be con-
nected from the source component to the
CAV6.6. The emitter is shown connected from
the IR receiver on the source component to the
source component’s IR emitter output port on
the rear on the CAV6.6. This type of configura-
tion allows independent control over more than
one identical source component. The IR from the
remote will be routed to the selected source.
When using the SRC2 remote, simply select
“UNO” at the top of the remote, select source
1-6 and operate the source.
To control the source components via IR from
the UNO-S2 Keypad, an IR emitter must be con-
nected from the source component to the
CAV6.6. The emitter is shown connected from
the IR receiver on the source component to the
source component’s IR emitter output port on
the rear on the CAV6.6. This type of configura-
tion allows independent control over more than
one identical source component. The IR from the
remote will be routed to the selected source.
When using the SRC2 remote, simply select
“UNO” at the top of the remote, select source
1-6 and operate the source.
Speakers
Connect the speakers to the amplified CAV6.6
zones 1 through 6 using a “Home Run” from the
individual amplified speaker outputs to the
speakers. Use the detachable modular snap
speaker connectors which are color coded and
labeled for easy installation. For most installations,
16 gauge 4-conductor wire is recommended.
Connect the speakers to the amplified CAV6.6
zones 1 through 6 using a “Home Run” from the
individual amplified speaker outputs to the
speakers. Use the detachable modular snap
speaker connectors which are color coded and
labeled for easy installation. For most installations,
16 gauge 4-conductor wire is recommended.
SAMPLE SYSTEM CONFIGURATION 1
Six Zones and Six Sources
Components List:
1 - CAV6.6 Controller
6 - UNO-S2 Keypads
3 - pair Advantage Iso-Mount™ Speakers
3 - pair Advantage Twist & Tilt™ Speakers
6 - 845.1 Micro Emitters