Bryston BP20 사용자 설명서
BP20/25 PreAmplifiers
General Specifications:
Frequency Response:
20Hz-20kHz +/- .05dB
20Hz-20kHz +/- .05dB
Maximum Output:
15 volts unbalanced, 30 volts balanced
15 volts unbalanced, 30 volts balanced
IMD/THD:
<0.0015% at 3 volts out
Sensitivity:
Balanced inputs:
1.00 V
UnBalanced line level inputs:
500 mV
Rated Noise:
-100dB (Ref. 500mV unbalanced input, 20-20kHz)
-103dB (Ref. 1 volt balanced input 20-20kHz)
-100dB (Ref. 500mV unbalanced input, 20-20kHz)
-103dB (Ref. 1 volt balanced input 20-20kHz)
XLR Connector Pin out (Balanced I/O):
Pin 1 ground, pin 2 positive, pin 3 negative
Pin 1 ground, pin 2 positive, pin 3 negative
Features:
20/25MC only)
Options:
module
Dimensions:
Standard version:
Standard version:
17” x 1.75” x 11”
43.18cm x 4.44cm x 28cm
43.18cm x 4.44cm x 28cm
Rack mount version:
19” x 1.75” x 11”
48.26cm x 4.44cm x 28cm
48.26cm x 4.44cm x 28cm
Weight:
17 lbs (7.5 kg)
MPS-1 POWER SUPPLY SPECIFICATIONS:
Dimensions:
7.75” x 4.525” x 2.36”h
Weight:
2.6 lb. (1182g)
Electrical:
120VAC/60Hz/29VA, Fuse: 315mA/250V time lag
230VAC/50Hz/29VA, Fuse: 160mA/250V time lag
240VAC/50Hz/29VA, Fuse: 160mA/250V time lag
230VAC/50Hz/29VA, Fuse: 160mA/250V time lag
240VAC/50Hz/29VA, Fuse: 160mA/250V time lag
Output:
+/-28VDC @ 350mA (56VDC @ 700mA)
All fuses are 5mm x 20mm, time lag type and are accessi-
ble only by removing the top cover. When replacing
fuses, disconnect the power cord before opening the unit!
ble only by removing the top cover. When replacing
fuses, disconnect the power cord before opening the unit!
Recommended replacement fuses:
for 100/120VAC models:
for 100/120VAC models:
Littlefuse 218.315
Bussmann GMC-315mA
Bussmann GMC-315mA
for 230/240VAC models:
Littlefuse 218.160
Bussmann GMC-160mA
Bussmann GMC-160mA
Additional Specifications for BP20/25DA:
Input Sample Rate:
16kHz to 108kHz.
Word Length:
16, 18, 20, 24 Bit
Data format:
SPDIF standard
Distortion:
< 0.002%, 20Hz-20kHz
Signal to Noise Ratio:
> 100dB
Frequency Response:
20Hz-20kHz +/- .1dB
Additional Specifications for BP20/25P
Phono Inputs:
Distortion:
Phono Inputs:
Distortion:
<0.005%, IM or THD, any frequency or combination of fre-
quencies from 20-20kHz, at rated output or below.
quencies from 20-20kHz, at rated output or below.
Rated Noise:
Phono: -80dBA referred to an input of 5 millivolts RMS @
1kHz
Phono: -80dBA referred to an input of 5 millivolts RMS @
1kHz
RIAA Accuracy:
Within less than +/- 0.05dB from 20-20kHz inclusive
Within less than +/- 0.05dB from 20-20kHz inclusive
Input sensitivity:
5mV
Additional Specifications for BP-25MC
Phono Inputs:
Phono Inputs:
Distortion:
<0.005%, 20-20kHz, with preamplifier driven to full rated
output
<0.005%, 20-20kHz, with preamplifier driven to full rated
output
Noise:
Equivalent to approximately 1000 ohm metal film register
(Thermal noise greater than 85dB below 0.6mV input,
unweighted)
Equivalent to approximately 1000 ohm metal film register
(Thermal noise greater than 85dB below 0.6mV input,
unweighted)
Gain: 16.5 or 22.5dB (internally reconfigurable)
Frequency Response: Below 5Hz to above 30kHz, within
less than +/- 0.5dB
less than +/- 0.5dB
Input sensitivity:
350uV (0.35mV)
2
Sept 2003