Sony STRDH520 사용자 설명서
34
GB
D:\NORM'S JOB\SONY HA\SO0109\STR-DH520\4263361111_GB\GB04CON_STR-DH520-
U2.fm
U2.fm
masterpage: Left
STR-DH520
4-263-361-11(1)
When error codes appear
1
Check the problem of the error.
*
xxx
represent a speaker channel
F
Front
S
Surround
SB
Surround back
FH
Front high
Depending on the error code, the speaker
channel may not appears.
channel may not appears.
2
Perform Auto Calibration again.
Press
Press
. “RETRY Y” will appears on the
display panel, then press
.
3
Repeat steps in “3: Confirming/saving
the measurement results” (page 33).
the measurement results” (page 33).
If a warning on the measurement result is
present, detailed information is displayed.
present, detailed information is displayed.
*
xxx
represent a speaker channel
FL
Front left
FR
Front right
CNT
Center
SL
Surround left
SR
Surround right
SBL
Surround back left
SBR
Surround back right
LH
Front left high
RH
Front right high
SW
Subwoofer
Depending on the measurement result, the speaker
channel may not appears.
channel may not appears.
To return to step 2 of
Press .
Tip
Depending on the position of the subwoofer, the
measurement results may vary. However, there will
be no problems even if you continue to use the
receiver with that value.
measurement results may vary. However, there will
be no problems even if you continue to use the
receiver with that value.
Display and explanation
E -
xxx
* 32
None of the speakers were detected. Make sure
that the optimizer microphone is connected
properly and perform the Auto Calibration
again. If the optimizer microphone is connected
properly but the error code still appears, the
optimizer microphone cable may be damaged.
that the optimizer microphone is connected
properly and perform the Auto Calibration
again. If the optimizer microphone is connected
properly but the error code still appears, the
optimizer microphone cable may be damaged.
E -
xxx
* 33
• None of the front speakers are connected or
only one front speaker is connected.
• The optimizer microphone is not connected.
• Either the left or right surround speakers is not
• Either the left or right surround speakers is not
connected.
• Surround back speakers or front high speakers
are connected even though surround speakers
are not meant to be connected. Connect the
surround speaker(s) to the SPEAKERS
SURROUND terminals.
are not meant to be connected. Connect the
surround speaker(s) to the SPEAKERS
SURROUND terminals.
The surround back speaker is connected only
to the SPEAKERS SURROUND BACK/
FRONT HIGH R terminals. When you
connect only one surround back speaker,
connect it to the SPEAKERS SURROUND
BACK/FRONT HIGH L terminals.
to the SPEAKERS SURROUND BACK/
FRONT HIGH R terminals. When you
connect only one surround back speaker,
connect it to the SPEAKERS SURROUND
BACK/FRONT HIGH L terminals.
• Either the front left high or front right high
speaker is not connected.
Checking the warning message
Display and explanation
W -
xxx
*
40
The measurement process has completed with high
noise level detection. You may be able to achieve
better results if you try in a quiet environment again.
noise level detection. You may be able to achieve
better results if you try in a quiet environment again.
W -
xxx
*
41
W -
xxx
*
42
The input from the microphone is too big. The
distance between the speaker and the microphone
may be too close. Set them apart and perform the
measurement again.
distance between the speaker and the microphone
may be too close. Set them apart and perform the
measurement again.
W -
xxx
*
43
The distance and position of a subwoofer cannot be
detected. This may be caused by noise. Try to
perform the measurement in a quiet environment.
detected. This may be caused by noise. Try to
perform the measurement in a quiet environment.
NO WARN
There is no warning information.
There is no warning information.