Sony STR-LV700R 사용자 설명서
Appe
ndix
masterpage:Right
filename[E:\SONY\STRLV700R_2nd\4249847121GB\4249847121\4249847121STRLV700RCEL
\01GB11APP_STR-LV700-CEL.fm]
\01GB11APP_STR-LV700-CEL.fm]
89
GB
model name1[STR-LV700R]
[4-249-847-12(1)]
• Check that the connecting cables are away from
transformers or motors, and at least 3 m away
from a television or fluorescent light.
from a television or fluorescent light.
There is no sound from the centre speaker.
• Make sure that the sound field function is on
(press the SOUND FIELD button).
• Select the CINEMA STUDIO EX mode
• Adjust the speaker level (page 21).
• Make sure that the centre speaker is set to
SMALL or LARGE (page 19).
There is no sound or only very low-level
sound from the surround speakers.
sound from the surround speakers.
• Make sure that the sound field function is on
(press the SOUND FIELD button).
• Select the CINEMA STUDIO EX mode
• Adjust the speaker level (page 21).
• Make sure that the surround speakers are set to
SMALL or LARGE (page 19).
There is no sound from the active subwoofer.
• Check that you have selected the subwoofer on the
receiver.
• Check that the subwoofer is set to YES (page 19).
• Depending on the sound field, audio may not be
output at the SUB WOOFER jack.
The surround effect cannot be obtained.
• Make sure that the sound field function is on
(press the A.F.D., MOVIE or MUSIC button).
• Sound fields do not function for signals with a
sampling frequency of more than 48 kHz.
Radio stations cannot be tuned in.
• Check that the antennae are connected securely.
Adjust the antennae and connect an external
antenna if necessary.
antenna if necessary.
• The signal strength of the stations is too weak
(when tuning in with automatic tuning). Use
manual tuning.
manual tuning.
• Make sure that you set the tuning interval
correctly (when tuning in AM stations manually).
• No stations have been preset or the preset stations
have been cleared (when scanning preset
stations). Preset stations (page 38).
stations). Preset stations (page 38).
• Press the black DISPLAY button so that the
frequency appears on the display.
RDS does not work.
• Make sure that you have tuned in an FM RDS
station.
• Select a stronger FM station.
The RDS information that you want does not
appear.
appear.
• Contact the radio station and find out whether they
provide the service in question. If so, the service
may be temporarily out of order.
may be temporarily out of order.
There is no picture or an unclear picture
appears on the television screen or monitor.
appears on the television screen or monitor.
• Select the appropriate input on the receiver.
• Set your television to the appropriate input mode.
The receiver is very hot and the fan does not
work.
work.
• During operation, the receiver can get
considerably hot, but this is not a sign of
malfunction. The fan starts automatically when
necessary.
malfunction. The fan starts automatically when
necessary.
Network Media
Network Media does not function.
• Verify that the remote batteries are correctly
inserted and that they are not spent (page 18)
• Press the N.MEDIA button on the remote before
attempting to use Network Media.
• If the screen freezes and the remote stops
functioning, or it becomes impossible to turn off
the receiver, Network Media may have become
unstable. Reset Network Media (page 80
“Resetting Network Media except the IP
address”). Alternatively, disconnect the power
cord from the power supply, and then reconnect it.
After resetting Network Media or reconnecting
the power cord, wait for approximately 20
seconds.
Note that all the Network Media settings are reset
to their defaults except the IP address, after
performing these operations.
the receiver, Network Media may have become
unstable. Reset Network Media (page 80
“Resetting Network Media except the IP
address”). Alternatively, disconnect the power
cord from the power supply, and then reconnect it.
After resetting Network Media or reconnecting
the power cord, wait for approximately 20
seconds.
Note that all the Network Media settings are reset
to their defaults except the IP address, after
performing these operations.
• If you turn off the receiver, it goes on standby
(waiting for remote operations). It still consumes
a small amount of power in this state. If you want
to completely turn off the receiver, disconnect it
from the power supply. Doing so resets all the
Network Media settings except the IP address.
Note that for about 20 seconds after connecting
the power cord to the power supply, switching the
receiver input to N.MEDIA has no effect on the
television.
a small amount of power in this state. If you want
to completely turn off the receiver, disconnect it
from the power supply. Doing so resets all the
Network Media settings except the IP address.
Note that for about 20 seconds after connecting
the power cord to the power supply, switching the
receiver input to N.MEDIA has no effect on the
television.
• If Network Media still does not function properly
20 seconds or more after connecting the power
cord to the power supply, it may be
malfunctioning. Consult your Sony service
representative.
cord to the power supply, it may be
malfunctioning. Consult your Sony service
representative.
continued