Sony MDS-JE520 사용자 설명서
5
EN
Getting Started
Hookups
Connecting the deck to an amplifier
Connect the amplifier to the LINE (ANALOG) IN/
OUT jacks using the audio connecting cords (supplied),
making sure to match the color-coded cords to the
appropriate jacks on the components: red (right) to red
and white (left) to white. Be sure to make connections
firmly to prevent hum and noise.
OUT jacks using the audio connecting cords (supplied),
making sure to match the color-coded cords to the
appropriate jacks on the components: red (right) to red
and white (left) to white. Be sure to make connections
firmly to prevent hum and noise.
ç
ç
ç
ç
ç
: Signal flow
Connecting the deck to a digital component such as
a CD player, DAT deck, digital amplifier, or another
MD deck
a CD player, DAT deck, digital amplifier, or another
MD deck
Connect the component through the DIGITAL
OPTICAL IN/OUT or DIGITAL COAXIAL IN
connectors with two optical cables (only one supplied)
and/or a coaxial digital connecting cable (not
supplied).
OPTICAL IN/OUT or DIGITAL COAXIAL IN
connectors with two optical cables (only one supplied)
and/or a coaxial digital connecting cable (not
supplied).
When using the optical cables
Take the caps off the connectors and then insert the plugs
parallelly until they click into place.
Be sure not to bend or tie together the optical cables.
parallelly until they click into place.
Be sure not to bend or tie together the optical cables.
ç
ç
ç
ç
ç
: Signal flow
When using the coaxial digital connecting cable
ç
ç
ç
ç
ç
: Signal flow
Note
If the optical cables and/or the coaxial digital connecting
cable are not connected properly, “Din Unlock” and “C71”
may alternate in the display.
cable are not connected properly, “Din Unlock” and “C71”
may alternate in the display.
MD deck
Amplifier
ç
Ç
L
R
L
R
LINE
(ANALOG)
OUT
IN
TAPE / MD
IN
OUT
z
Automatic conversion of digital sampling rates
during recording
during recording
A built-in sampling rate converter automatically
converts the sampling frequency of various digital
sources to the 44.1 kHz sampling rate of your MD deck.
This allows you to record sources such as 32- and 48-
kHz DAT or satellite broadcasts, as well as compact
discs and other MDs.
converts the sampling frequency of various digital
sources to the 44.1 kHz sampling rate of your MD deck.
This allows you to record sources such as 32- and 48-
kHz DAT or satellite broadcasts, as well as compact
discs and other MDs.
Note
If “Din Unlock” alternates with “C71”, or “Cannot Copy”
appears in the display, recording through the digital
connector is not possible. In this case, record the program
source through the LINE (ANALOG) IN jacks with the
INPUT switch set at ANALOG.
appears in the display, recording through the digital
connector is not possible. In this case, record the program
source through the LINE (ANALOG) IN jacks with the
INPUT switch set at ANALOG.
Setting the voltage selector (only on
models supplied with a voltage selector)
models supplied with a voltage selector)
Check that the voltage selector on the rear panel of the
deck is set to the local power line voltage. If not, set
the selector to the correct position using a screwdriver
before connecting the AC power cord to an AC outlet.
deck is set to the local power line voltage. If not, set
the selector to the correct position using a screwdriver
before connecting the AC power cord to an AC outlet.
Connecting the AC power cord
Connect the AC power cord to a wall outlet or to the
outlet of a timer.
outlet of a timer.
MD deck
Digital component
MD deck
Digital component
DIGITAL
OUT
IN
OPTICAL
DIGITAL
OUT
IN
IN
OPTICAL
COAXIAL
ç
Ç
DIGITAL
COAXIAL
Ç
OUT
DIGITAL
OUT
IN
IN
OPTICAL
COAXIAL
110 – 120V
220 – 240V