JVC GET0634-005A 사용자 설명서
4
Heat sink
Installation
This unit is designed to operate on 12 V DC, NEGATIVE ground
electrical systems. If your vehicle does not have this system, a
voltage inverter is required, which can be purchased at JVC car
audio dealers.
electrical systems. If your vehicle does not have this system, a
voltage inverter is required, which can be purchased at JVC car
audio dealers.
Prepare these before installation....
Warnings
• To prevent short circuits:
– Disconnect the battery’s negative terminal and make all electrical connections before installing the unit.
– Cover the terminals of the UNUSED leads with insulating tape.
• Be sure to ground this unit to the car’s chassis again after installation.
• Replace the fuse with one of the specified rating.
• Connect speakers with a maximum power of more than 50 W
– Disconnect the battery’s negative terminal and make all electrical connections before installing the unit.
– Cover the terminals of the UNUSED leads with insulating tape.
• Be sure to ground this unit to the car’s chassis again after installation.
• Replace the fuse with one of the specified rating.
• Connect speakers with a maximum power of more than 50 W
(impedance of 4 Ω to 8 Ω). Otherwise, change the <AMP GAIN> setting.
(See “Menu operations” on page 3.)
(See “Menu operations” on page 3.)
• The heat sink becomes very hot after use. Be careful not to touch it
when removing this unit.
Parts List
A Hard
case
.................................................................................1
B Control
panel.........................................................................1
C Sleeve
.........................................................................................1
D Trim
plate
.................................................................................1
E Power
cord
..............................................................................1
F Handles
.....................................................................................2
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
In-dash mounting
When installing the unit without using the sleeve
Removing the unit
Release the rear section first...
Install the unit at an
angle of less than 30˚.
angle of less than 30˚.
Do the required
electrical connections.
electrical connections.
Bend the appropriate tabs to hold
the sleeve firmly in place.
the sleeve firmly in place.
When you stand the unit, be careful
not to damage the fuse on the rear.
not to damage the fuse on the rear.
Bracket*
Pocket
Flat head screws (M5 × 8 mm)*
* Not supplied for this unit.
Electrical connections
IMPORTANT: A custom wiring harness (separately purchased) which is suitable for your car is recommended
for connection between the unit and your car.
• Consult your JVC car audio dealer or a company supplying kits for details.
for connection between the unit and your car.
• Consult your JVC car audio dealer or a company supplying kits for details.
PRECAUTIONS on power supply and speaker connections
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be
seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your
car.
Rear ground terminal
15 A fuse
Antenna input
Reset the unit
Black
Fuse block
Ignition switch
Blue (white stripe)
Blue
Red
Yellow *
3
To the metallic body
or chassis of the car
or chassis of the car
To an accessory
terminal
terminal
To a live terminal
(constant 12 V)
(constant 12 V)
White
White (black stripe)
Gray
Gray (black stripe)
Green
Green (black stripe)
Purple
Purple (black stripe)
Front speaker
(left)
(left)
Front speaker
(right)
(right)
Rear speaker
(left)
(left)
Rear speaker
(right)
(right)
Signal cord *
1
Y-connector *
1
Remote lead
To the blue (white stripe)
lead of the unit
lead of the unit
Rear speakers or subwoofer
Make the <L/O MODE> setting accordingly.
(See “Menu operations” on page 3.)
Make the <L/O MODE> setting accordingly.
(See “Menu operations” on page 3.)
JVC Amplifier
Connecting the external amplifier or subwoofer
*
2
Connect only the front speakers
if your speaker system is two-
speaker system.
if your speaker system is two-
speaker system.
To the automatic antenna if any
(250 mA max.)
(250 mA max.)
To the remote lead of other
equipment (200 mA max.)
equipment (200 mA max.)
Steering wheel remote input
*
1
Not supplied for this unit.
*
2
Firmly attach the ground wire to the metallic body or to the chassis of the car—to the
place uncoated with paint.
place uncoated with paint.
*
3
Before checking the operation of this unit prior to installation, this
lead must be connected, otherwise the power cannot be turned on.
lead must be connected, otherwise the power cannot be turned on.
EN_KD-R514[UI]_1.indd 4
EN_KD-R514[UI]_1.indd 4
11/30/09 10:51:17 AM
11/30/09 10:51:17 AM