Panasonic TH-L32XM5K 사용자 설명서

  Music

MP3

.mp3

–

NOTE
•  Some fi les may not be played back even if they fulfi l these conditions.

•  Do not use two-byte characters or other special codes for data.

•  Th e device may become unusable with this TV if the fi le or folder names are changed.

When you receive the stereo / bilingual sound system, sound output modes can be selected 
by pressing the Sound Selection button.

Mode 

Indicator

NICAM .......Used in New Zealand, Singapore, Hong Kong, etc.

Mode 

Indicator

No 

Indicator

I 

II 

A2 (German) .......Used in Australia, Malaysia, etc.

Mode 

Indicator

No 

Indicator

• If the stereo signal is poor or the receiving conditions are not optimum or if STEREO:MONO 

automatic switching occurs, it is recommended you switch from STEREO to MONO.

• Even when the contents of the receiving signal undergo changes, selection mode is kept intact.

• When the receiving conditions deteriorate, listening will be easier if the mode is set to the 

MONO position, using the Sound Selection button.

• DUAL, also known as DUAL MONO or as BILINGUAL is not currently transmitted in some 

countries.

Before requesting service or assistance, please follow these simple guides to resolve the 
problem. If problem still persists, please contact your local Panasonic dealer.

•  Check the position, direction, and connection 

of the aerial.

•  Keep the space between the TV and RF cable.

•  Is the TV in “AV mode”?
•  Is the mains lead plugged into the socket outlet?
•  Is the TV turned On?
•  Check [Picture Menu] and volume.
•  Check all required cables and connections are 

firmly in place.

•  Follow the message’s instructions. 
•  If the problem persists, contact your local 

Panasonic dealer.

•  This is a characteristic of liquid crystal panels 

and is not a problem. The liquid crystal panel is 
built with very high precision technology giving 
you fine picture details. Occasionally, a few non-
active pixels may appear on the screen as a fixed 
point of red, green, blue or black. 
Please note this does not affect the performance 
of your LCD and it is not a quality problem.

•  There are some looseness around the panel to 

prevent damage to the panel.
The panel might move slightly when it is pushed 
with a finger, and clattered sound might be 
heard. This is not a malfunction.

•  Auto power standby function is activated.
•  The TV enters Standby mode about 30 minutes 

after broadcasting ends.

•  Is “Sound Mute” active?
•  Is the volume set to the minimum?

•  Are the batteries installed correctly?
•  Has the TV been switched On?
•  Point the remote control directly at the front of 

the TV (within a 30 degree angle of the front of 
the TV).

•  Situate the TV away from sunshine or other 

sources of bright light not to shine on the TV’s 
remote control signal receiver.

•  Set the sound setting of the connected equipment 

to “2ch L.PCM”.

•  Check the [HDMI Input] setting in the Sound 

Menu.

•  If digital sound connection has a problem, select 

analogue sound connection.

•  Sound signal reception may be deteriorated.
•  Set [MPX] in the Sound Menu to [Mono].

•  Is the HDMI cable connected properly? 
•  Turn Off the TV and equipment, then turn them 

On again. 

•  Check an input signal from the equipment.
•  Use an equipment compliant with 

EIA/CEA-861/861B.

•  Is [Colour] or [Contrast] in the Picture Menu set 

to the minimum?

(no sound or low volume)
•  Reset channel.

•  Change the setting of [P-NR] in the Picture 

Menu (to remove noise).

•  Check nearby electrical products (car, 

motorcycle, fluorescent lamp).

•  Turn off the TV Mains power, then turn it on 

again.

15

TH-L32XM5KMTX_fold_EN.indd   15

TH-L32XM5KMTX_fold_EN.indd   15

6/1/2012   8:26:18 AM

6/1/2012   8:26:18 AM