Sony STR-DB895D 사용자 설명서
masterpage:Left
lename[E:\SEM_Janet\Data_DB895D\J9050665_2598514111DB895DCEL\2598514111\GB09
ADD_STR-DB895D-CEL.fm]
62
GB
model name1[STR-DB895D]
[2-598-514-11(1)]
The surround effect cannot be obtained.
• Make sure the sound field function is on (press
MOVIE or MUSIC).
• Sound fields do not function for the signals with a
sampling frequency of more than 48 kHz.
Dolby Digital or DTS multi channel sound is
not reproduced.
not reproduced.
• Check that the playing DVD, etc. is recorded in
Dolby Digital or DTS format.
• When connecting the DVD player, etc. to the
digital input jacks of this receiver, check the audio
setting (settings for the audio output) of the
connected component.
setting (settings for the audio output) of the
connected component.
Recording cannot be done.
• Check that the components are connected
correctly.
• Select the source component with INPUT
SELECTOR.
• Make sure that INPUT MODE is set to
• Make sure that INPUT MODE is set to “COAX
IN” or “OPT IN” (page 41) before recording from
a digital component connected to the DIGITAL
OPTICAL MD/TAPE OUT jack.
a digital component connected to the DIGITAL
OPTICAL MD/TAPE OUT jack.
You cannot name the preset station.
• You cannot name DAB/FM RDS stations.
“DAB _ _ _ _” appears in the display (DAB
reception only).
reception only).
• Check all antenna connections, then press
TUNING + or TUNING – to select a service.
• The current DAB service is not available. Press
TUNING + or TUNING – to select a different
service.
service.
• If you have moved to another area, some services/
frequencies may have changed and you may not
be able to tune into your usual broadcast. Perform
the DAB INITIAL SCAN procedure to re-register
the contents of broadcast. (Performing this
procedure clears all previously stored presets.)
(page 27).
be able to tune into your usual broadcast. Perform
the DAB INITIAL SCAN procedure to re-register
the contents of broadcast. (Performing this
procedure clears all previously stored presets.)
(page 27).
The FM reception is poor.
• Use a 75-ohm coaxial cable (not supplied) to
connect the receiver to an outdoor FM antenna as
shown below. If you connect the receiver to an
outdoor antenna, ground it against lightning. To
prevent a gas explosion, do not connect the ground
wire to a gas pipe.
shown below. If you connect the receiver to an
outdoor antenna, ground it against lightning. To
prevent a gas explosion, do not connect the ground
wire to a gas pipe.
Radio stations cannot be tuned in.
• Check that the antennas are connected securely.
Adjust the antennas and connect an external
antenna if necessary.
antenna if necessary.
• The signal strength of the stations is too weak
(when tuning in with automatic tuning). Use direct
tuning.
tuning.
• Make sure you set the tuning interval correctly
(when tuning in AM stations with direct tuning).
• No stations have been preset or the preset stations
have been cleared (when tuning by scanning
preset stations). Preset the stations (page 28).
preset stations). Preset the stations (page 28).
• Press DISPLAY repeatedly so that the frequency
appears in the display.
RDS does not work.
• Make sure that you’re tuned to an FM RDS
station.
• Select a stronger FM station.
The RDS information that you want does not
appear.
appear.
• Contact the radio station and find out whether they
actually provide the service in question. If so, the
service may be temporarily out of order.
service may be temporarily out of order.
AM
COAXIAL
ANTENNA
Outdoor FM antenna
Ground wire
(not supplied)
(not supplied)
To ground
Receiver
GB01COV_STR-DB895D-CEL.book Page 62 Wednesday, June 15, 2005 9:28 AM