Honeywell R4140G 사용자 설명서

R4140G FLAME SAFEGUARD PROGRAMMING CONTROLS

60-2337—3

5

W136A Test Meter (includes 117053 Meter Connector

Plug); has SPL position with damping for testing self-
checking flame detection systems.

117053 Meter Connector Plug (for older W136A models).
123514A Flame Simulator (for use with R7247A

Rectification Amplifiers).

123514B Flame Simulator (for use with R7249A Ultraviolet

Amplifiers).

139695C (Series 1 and 2) Cover with reset button; heavy

duty, metal cover for outside panel mounting.

202050C (Series 3) Cover with reset button; heavy duty,

metal cover for outside panel mounting.

118760B (Series 1 and 2) Remote Reset Cover; heavy

duty, metal cover with remote reset assembly; 120V,
60 Hz solenoid.

202051B (Series 3) Remote Reset Cover; heavy duty,

metal cover with remote reset assembly; 120V, 60 Hz
solenoid.

R1061012 Ignition Cable; for ignition installations in a high

temperature environment; rated at 350

°

F (177

°

C) for

continuous duty, and up to 500

°

F (260

°

C) for

intermittent use; tested to 25,000V.

R1298020 Cable; for flame detector (F lead-wire)

installations in a high temperature environment; rated
up to 400

°

F (204

°

C) for continuous duty; tested for

operation up to 600V and breakdown up to 7500V.

R1239001 High Tension Ignition Cable; for ignition

installations in a contaminating environment; very
resistant to severe conditions of oil, heat, and corona,
and tested to withstand high voltages up to
25,000V rms in a salt bath for one minute without
breakdown; rated at 200

°

F (93

°

C) for continuous duty,

and up to 350

°

F (197

°

C) for intermittent use.

Q624A Solid State Spark Generator; prevents detection of

ignition spark when properly applied with flame
detection systems using C7027, C7035, or C7044
Minipeeper Ultraviolet Flame Detectors. For use only
with gas pilots.

FSP5004 Tester; provides a quick operational check of

most R4140 Flame Safeguard Programming Controls.

Q520E1002 Service Tool; allows any of the programmer

terminals to be monitored while the programmer is
operating.

Rectification

Green

No

R7247A

2 to 4 sec

Gas

Rectifying

Flame Rods

Holders

a

: C7004, C7007, C7011.

Complete assemblies: C7005,

C7008, C7009, Q179.

R7247A,
R7247B

b

2 to 4 sec

Oil

Rectifying

Photocells

c

C7003, C7010, C7013, C7014.

Gas,

Oil,

Coal

Ultraviolet

(Purple

Peeper)

C7012A or C.

Dynamic

Self-

Check

R7147B

b

2 to 4 sec

Gas

Rectifying

Flame Rods

Holders

a

: C7004, C7007, C7011.

Complete Assemblies: C7005,

C7008, C7009, Q179.

R7247C

d

2 to 4 sec

Gas,

Oil,

Coal

Ultraviolet

(Purple

Peeper)

C7012E or F

Infrared

Red

No

R7248A

2 to 4 sec

Gas,

Oil,

Coal

Infrared

(Lead

Sulfide)

C7015.

Dynamic

Ampli-

Check®

R7248B

b

2 to 4 sec

Gas,

Oil,

Coal

Infrared

(Lead

Sulfide)

C7015.

Ultraviolet

Purple

No

R7249A

2 to 4 sec

Gas,

Oil

Ultraviolet

(Minipeeper)

C7027, C7035, C7044.

Blue

Dynamic

Self-

Check

R7476A

d

2 to 4 sec

Gas,

Oil,

Coal

Ultraviolet

(Adjustable

Sensitivity)

C7076.

NOTE:

Neither the R414G1114 or the R4140G1122 can be used with the C7012E or F Purple Peeper Ultraviolet Flame
Detector and with the R7247C Dynamic Self-Check Amplifier.

a

Order flame rod separately; see Instructions for the holder.

b

Circuitry tests the flame signal amplifier at least 150 times a minute during burner operation and shuts down the burner if the
amplifier fails.

c

Use only Honeywell part no. 38316 Photocell.

d

Circuitry tests all electronic components in the flame detection system (amplifier and detector) 60 to 240 times a minute during
burner operation and shuts down the burner if the detection system fails.