Panasonic SC-MAX770 사용자 설명서

“USB A NO DEVICE”
“USB B NO DEVICE”
• The USB device is not connected. Examine the

connection.

“DEVICE FULL”
• You cannot do recording because the remaining

recording time of the USB device is less than the total
time of the music source.
Change to a USB device which has enough recording
time and do the recording again.

“ERROR”
• An incorrect operation was done. Read the instructions

and try again.

“ERROR” (during recording)
• You cannot select other playback source (example:

radio, USB etc.) or press [:] or [9] during
recording. Stop the recording function.

• You cannot open the disc tray when recording from an

AM source.

“F61”
• Examine and correct the speaker cords connection.
• Disconnect the USB device. Switch off the system and

then switch it on again.

“F70”
• Examine the Bluetooth

device.

• Disconnect the Bluetooth

device. Switch off the

system and then switch it on again.

“F77”
• Switch off the system and then switch it on again.

“NO PLAY”
“UNSUPPORT”
• Examine the content. You can only play supported

format.

• The files in the USB device can be corrupted. Format

the USB device and try again.

• The unit may have a problem. Turn the unit off and

then on again.

“NO TRACK”
• There is no album or track in the USB device or the

internal memory.

“PLAYERROR”
• You played an unsupported MP3 file. The system will

skip that track and play the next one.

“REMOTE 1”
“REMOTE 2”
• The remote control and the main unit are using

different codes. Change the code of the remote
control.
- When “REMOTE 1” is shown, press and hold [OK]

and [1] for a minimum of 4 seconds.

- When “REMOTE 2” is shown, press and hold [OK]

and [2] for a minimum of 4 seconds.

“TEMP NG”
• The temperature protection circuit has been activated,

and the system will switch off. Let the unit cool down
before switching it on again.

• Check that the ventilation opening of the unit is not

obstructed.

• Ensure this unit is well ventilated.

“USB OVER CURRENT ERROR”
• The USB device is using too much power.

Disconnect the USB device, switch off the system and
then switch on again.

“VBR”
• The system cannot show the remaining play time for

variable bit rate (VBR) tracks.

System memory reset (initialization)

Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.

Disconnect the AC power supply cord.

While you press and hold [Í/I] on the main unit,
connect the AC power supply cord again.
Continue to press and hold the button (approximately
10 seconds) until “- - - - - - - -” is shown.

Release [Í/I].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.

Remote control code

When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.

Preparation
Press [RADIO/EXT-IN] to select “AUX 1” or “AUX 2”.

Press and hold [RADIO/EXT-IN] on the main unit
and [2] on the remote control until “REMOTE 2”
is shown.

Press and hold [OK] and [2] for a minimum of
4 seconds.

Press and hold [RADIO/EXT-IN] on the main unit
and [1] on the remote control until “REMOTE 1”
is shown.

Press and hold [OK] and [1] for a minimum of
4 seconds.

Main unit displays

To set the code to “REMOTE 2”

To set the code to “REMOTE 1”

SC-MAX770PU_eng.book 18 ページ２０１４年３月６日　木曜日　午後２時５４分