Panasonic WV-NS324 사용자 설명서
-47-
Note:
Input an external alarm signal of more than
100 ms.
3. Alarm Preset
Select the item by pressing the [o] button, and
click the [SET] button.
click the [SET] button.
1POSI:
Camera performs according to Preset posi-
tion 1 when there is input at ALARM IN 1.
2POSI:
Camera performs according to Preset posi-
tion 2 when there is input at ALARM IN 2.
OFF:
No alarm preset used. Set Preset position 1
and 2 in advance when using this function.
The default setting is OFF.
4. E-mail Notice Setup
E-mail Notice:
In ON position, an e-mail is sent
when alarm arises. The default is OFF.
E-mail Server Address:
Input the Mail Server
Address in not more than 128 numbers or
small letters of one byte. When using DNS,
input "host name. Domain name".
small letters of one byte. When using DNS,
input "host name. Domain name".
Sender E-mail Address:
Input the Sender E-mail
Address. The default is NW_Camera.
It is named "NW_Camera@(IP address of cam-
era)" when input without the @ mark.
It is named "NW_Camera@(IP address of cam-
era)" when input without the @ mark.
• Select ON or OFF for Attach Image.
ON:
Attaches the alarmed picture to the e-
mail.
OFF:
No picture attached. The default setting
is OFF.
• Click the [SET & REBOOT] button.
• Enter up to 4 destination e-mail addresses,
• Enter up to 4 destination e-mail addresses,
and click the [SET] button.
• Click the [DEL (delete)] button after selecting
an unwanted e-mail address to delete it.
Notes:
• The e-mail address of the sender is one and
the same as that of the administrator.
• Sending mails is not possible in an environ-
ment that requires authentication for SMPTE or
POP3.
POP3.
5. Recording Setup
The image fields before and after an alarm input
are stored in the memories of the cameras.
are stored in the memories of the cameras.
• Set the number of image frames for pre
recording (0 - 20) and post recording (1 - 20).
• Set the recording rate (fps: frame per second).
Pre-recording rates:
1/10, 1/5, 1/3, 1/2, 1, 2,
3.3, 5 ..... The default setting is 1.
Post-recording rates:
1/10, 1/5, 1/3, 1/2, 1, 2,
3.3, 5, 10 ..... The default setting is 1.
• Click the [SET & REBOOT] button.
6. Panasonic Protocol Setup
• Select ON or OFF.
ON:
Sends alarm notice mails to the cus-
tomized destinations.
OFF:
Does not send.
• Enter the destination port. The port number
is exclusively assigned to this function, and
any other usage is not allowed.
any other usage is not allowed.
• Enter a number of retries from 1 to 25.
• Click the [SET] button.
• Enter a maximum of 8 destination IP
• Enter a maximum of 8 destination IP
addresses, and click the [SET] button.
• Click the [DEL (delete)] button after select-
ing an unwanted destination to cancel it.
Destination IP Address
Input the Panasonic Protocol Destination IP
Address, and click the [SET] button.
Input the Panasonic Protocol Destination IP
Address, and click the [SET] button.
7. External Terminal Output Setup
Alarm output is supplied from the Alarm OUT con-
nector when Terminal 1, Terminal 2 or VMD is in
use.
nector when Terminal 1, Terminal 2 or VMD is in
use.
• Select a signal type :
Pulse:
Holds active status during the specified
time width.
Latch:
Holds active status until reset manually.
• Enter the pulse width (necessary number x
100 ms) if you selected Pulse. A number from
1 to 100 is applicable.
1 to 100 is applicable.
• Click the [SET & REBOOT] button.
8. External Alarm Reset
• Click the [Alarm Reset] button to cancel the
activated alarm.
Note:
Wait around 5 seconds or more when exe-
cuting [SET&REBOOT] button.
■
FTP Client Setup
Image files can be transferred to the FTP server within
the scheduled time zone.
the scheduled time zone.