JVC TK-C210FW 사용자 설명서
8
Introduction (continued)
Camera
A
Mounting hole (elliptical) x 4
Use these when mounting the camera to the
Use these when mounting the camera to the
NOTE:
electrical box. (
A pg. 22)
When installing the camera onto the electric
box, install it using the supplied adaptor ring.
box, install it using the supplied adaptor ring.
B
Mounting hole (round) x 4
Use these when mounting the camera to the
ceiling or wall. (
Use these when mounting the camera to the
ceiling or wall. (
A pg. 18, 20)
C
Outer Case
Use this in the following cases:
Use this in the following cases:
● When mounting the camera directly to the
ceiling or on the wall. (
A pg. 20)
● When mounting the camera to the electrical
box. (
A pg. 22)
D
Dome Cover
The dome cover is fragile. Take care when
handling it.
The dome cover is fragile. Take care when
handling it.
E
Wiring Hole
Break and use this when drawing the cable
from the camera unit without drilling a hole in
the ceiling. (
Break and use this when drawing the cable
from the camera unit without drilling a hole in
the ceiling. (
A pg. 22)
F
Input Power cable
DC 12 V Input: Red (+12 V), Black (GND)
AC 24 V Input: Non-polar. (
DC 12 V Input: Red (+12 V), Black (GND)
AC 24 V Input: Non-polar. (
A pg. 15)
G
Alarm signal cable (TK-C215V12 only)
Yellow (ALARM IN), Gray (ALARM GND).
(
Yellow (ALARM IN), Gray (ALARM GND).
(
A pg. 15)
H
Protection Cover
Upon connecting the coaxial cable, protect it
by insulating the metal part of the BNC
connector from the ceiling structure.
Upon connecting the coaxial cable, protect it
by insulating the metal part of the BNC
connector from the ceiling structure.
I
Video signal output connector (BNC)
(
(
A pg. 14)
Name of Parts
B
D
C
A
I
H
G
F
G
F
A
E
B
TK-C215V12 only
9
Camera (Interior)
The picture below shows the camera when the
dome cover and outer case are removed.
Procedures for removal. (
dome cover and outer case are removed.
Procedures for removal. (
A pg. 18
AEmbedding
the camera to the ceiling
B, Step 3. to Step 4.)
J
Fastening Screw (x 3)
Screw head of the ceiling mount bracket O to
be used when embedding the camera to the
ceiling.
Screw head of the ceiling mount bracket O to
be used when embedding the camera to the
ceiling.
K
[MONITOR] terminal (RCA pin)
(
(
A pg. 23)
L
Camera Unit
M
Fall Prevention Wire Fastening Hook
N
Fall Prevention Wire (Supplied) and Wire
Mounting Screw
Connect the camera unit L and the outer
case C using the fall prevention wire fastening
hook M.
Mounting Screw
Connect the camera unit L and the outer
case C using the fall prevention wire fastening
hook M.
O
Ceiling Mount Bracket (x 3)
This is used as a bracket when embedding the
camera to the ceiling. (
This is used as a bracket when embedding the
camera to the ceiling. (
A pg. 18)
P
Camera Fastening Screw
Use this to fasten the camera unit L to the
outer case C. To remove. (
Use this to fasten the camera unit L to the
outer case C. To remove. (
A pg. 18, 20)
Q
Tilt Lock screw
Tighten the screw to ensure that camera's
shooting direction does not go out of
alignment when it is used in a location with
strong vibration. (
Tighten the screw to ensure that camera's
shooting direction does not go out of
alignment when it is used in a location with
strong vibration. (
A pg. 24)
R
Imaging Direction mark
Install the camera by aligning the imaging
direction with the arrow mark.
Install the camera by aligning the imaging
direction with the arrow mark.
S
Rotation Knob
Rotate the lens unit to adjust the inclination of
the image (to be turned).
Rotate the lens unit to adjust the inclination of
the image (to be turned).
T
Rotation Center Mark
(
(
A pg. 24)
U
Pan fastening Screw
Ensure to loosen the screw before setting.
Further tighten the screw to ensure that
camera's shooting direction does not go out of
alignment only when it is used in a location
with strong vibration. (
Ensure to loosen the screw before setting.
Further tighten the screw to ensure that
camera's shooting direction does not go out of
alignment only when it is used in a location
with strong vibration. (
A pg. 24)
V
Fall Prevention Wire mounting hole &
Screw
(Fall Prevention Wire not included.)
Screw
(Fall Prevention Wire not included.)
V
M
N
O
J
L
K
N
P
Q
R
S
T
U
Camera Unit (Rear)
Lens
(
(
A Next page)
*TK-C215V4 is used in the above illustration