John Deere 225D LC 사용자 설명서

 Net engine power is with standard equipment including air cleaner,
exhaust system, alternator, and cooling fan at test conditions per
ISO9249. No derating is required up to 10,000-ft. (3050 m) altitude.

 Specifications and design subject to change without notice. Wherever applicable, specifications are in accordance with SAE standards. 
Except where otherwise noted, these specifications are based on units with full fuel tanks and 175-lb. (79 kg) operators; a 135D unit
with 30-in. (762 mm), 0.66-cu.-yd. (0.50 m

3

), 1,023-lb. (464 kg) bucket, 9-ft. 11-in. (3.01 m) arm, 28-in. (700 mm) triple semi-grouser

shoes, and 8,113-lb. (3680 kg) counterweight; and a 225D LC unit with 42-in. (1067 mm), 1.09-cu.-yd. (0.83 m

3

), 1,731-lb. (721 kg) 

heavy-duty bucket, 9-ft. 7-in. (2.91 m) arm, 32-in. (800 mm) triple semi-grouser shoes, and 16,710-lb. (7586 kg) counterweight.

02-04-10

 135D  225D 

●  ● 

Meets EPA Tier 3/EU Stage IIIA emissions

●  ● 

Auto-idle system

●  ● 

Batteries (two 12 volt), 180-min. reserve capacity

●  ● 

Coolant recovery tank

●  ● 

Dual-element dry-type air filter

●  ● 

Electronic engine control

●  ● 

Enclosed fan guard (conforms to SAE J1308)

●  ● 

Engine coolant to –34 deg. F (–37 deg. C)

●  ● 

Fuel filter with water separator

●  ● 

Full-flow oil filter

●  ● 

Turbocharger with charge air cooler

●  ● 

Muffler, under hood, with vertical curved end

  

  exhaust 

stack

●  ● 

Radiator, oil cooler, and intercooler with dust-

  

  protective 

net

●  ● 

Glow-plug start aid

●  ● 

500-hour engine oil-change interval

●  ● 

70% (35 deg.) off-level capability

●  ● 

Isolation mounted

●  ● 

Engine oil-drain coupler

    

 

●  ● 

Reduced-drift valve for boom down, arm in

●  ● 

Auxiliary hydraulic valve section

●  ● 

Spring-applied, hydraulically released automatic

  

  swing 

brake

●  ● 

Auxiliary hydraulic-flow adjustments through

  

  monitor

   

● 

Auto power lift

●  ● 

5,000-hour hydraulic oil-change interval

 

▲

▲

Auxiliary hydraulic lines

 

▲

▲

Auxiliary pilot and electric controls

 

▲

▲

Hydraulic filter restriction indicator kit

 

▲

▲

Load-lowering control device

 

▲

▲

Single-pedal propel control

 

▲

▲

Control pattern-change valve

    

 

●  ● 

Planetary drive with axial piston motors

  ●  ● 

Propel motor shields

  ●  ● 

Spring-applied, hydraulically released automatic

  

  propel 

brake

 ●   

Track guides, front idler

   

● 

Track guides, front idler and center

  ●  ● 

Two-speed propel with automatic shift

  ●   

Upper carrier roller (1)

   

● 

Upper carrier rollers (2)

●  ● 

Sealed and lubricated track chain

 135D  225D 

 

▲

Rubber crawler pad, 20 in. (500 mm)

 

▲

Triple semi-grouser shoes, 24 in. (600 mm)

 

▲ ▲

Triple semi-grouser shoes, 28 in. (700 mm)

   

▲

 

Triple semi-grouser shoes, 32 in. (800 mm)

 

▲

Undercarriage with blade

    

 

●  ● 

Right- and left-hand mirrors

  ●  ● 

Vandal locks with ignition key: Cab door / Fuel

   

 

cap / Service doors / Toolbox

  ●  ● 

Remote-mounted engine oil and fuel filters

    

 

●  ● 

Centralized lubrication system

  ●  ● 

Dirt seals on all bucket pins

  ●  ● 

Less boom and arm

  ●  ● 

Oil-impregnated bushings

  ●  ● 

Reinforced resin thrust plates

  ●  ● 

Tungsten carbide thermal coating on arm-to-

  

  bucket 

joint

   

▲

Arm, 7 ft. 11 in. (2.42 m)

 

▲

Arm, 8 ft. 3 in. (2.52 m)

   

▲

Arm, 9 ft. 7 in. (2.91 m)

 

▲

Arm, 9 ft. 11 in. (3.01 m)

 

▲

▲

Attachment quick-couplers

 

▲

▲

Boom cylinder with plumbing to mainframe for

   

 

less boom and arm

 

▲

▲

Buckets: Ditching / Heavy duty / Heavy-duty

   

 

high capacity / Side cutters and teeth

 

▲

▲

Material clamps

    

 

●  ● 

Adjustable independent control positions (levers-

  

  to-seat, 

seat-to-pedals)

●  ● 

AM/FM radio

●  ● 

Auto climate control/air conditioner, 20,000

   

 

Btu/hr. (5.9 kW), with heater and pressurizer

●  ● 

Built-in operator’s manual storage compart-

   

 

ment and manual

●  ● 

Cell-phone power outlet, 12 volt, 60 watt, 5 amp

●  ● 

Coat hook

●  ● 

Deluxe suspension cloth seat with 4-in.

   

 

(100 mm) adjustable armrests

●  ● 

Floor mat

●  ● 

Front windshield wiper with intermittent speeds

●  ● 

Gauges (illuminated): Engine coolant / Fuel

●  ● 

Horn, electric

●  ● 

Hour meter, electric

●  ● 

Hydraulic shutoff lever, all controls

 135D  225D 

●  ● 

Hydraulic warm-up control

●  ● 

Interior light

●  ● 

Large cup holder

●  ● 

Machine Information Center (MIC)

●  ● 

Mode selectors (illuminated): Power modes –

   

 

three / Travel modes – two with automatic

   

 

shift / Work mode – one

●  ● 

Multifunction, color LCD monitor with: Diagnostic

   

 

capability / Multiple-language capabilities / Main-

   

 

tenance tracking / Clock / System monitoring

   

 

with alarm features: Auto-idle indicator, engine

   

 

air cleaner restriction indicator light, engine

   

 

check, engine coolant temperature indicator

   

 

light with audible alarm, engine oil pressure

   

 

indicator light with audible alarm, low-alternator-

   

 

charge indicator light, low-fuel indicator light,

   

 

fault-code alert indicator, fuel-rate display,

   

 

wiper-mode indicator, work-lights-on indicator,

   

 

and work-mode indicator

●  ● 

Motion alarm with cancel switch (conforms to

  

  SAE 

J994)

   

● 

Power-boost switch on right console lever

●  ● 

Auxiliary hydraulic control switches in right

  

  console 

lever

●  ● 

SAE two-lever control pattern

●  ● 

Seat belt, 2 in. (51 mm), retractable

●  ● 

Tinted glass

●  ● 

Transparent tinted overhead hatch

●  ● 

Hot/cold beverage compartment

 

▲

▲

Seat belt, 3 in. (76 mm), non-retractable

 

▲

▲

Monitor system with alarm features: Hydraulic

   

 

oil filter restriction indicator light

 

▲

▲

Air-suspension heated seat

 

▲

▲

24- to 12-volt D.C. radio convertors, 10 amp

 

▲

▲

Circulation fan

 

▲

▲

Protection screens for cab front, rear, and side

 

▲

▲

Window vandal protection covers

   

 

●  ● 

50-amp alternator

●  ● 

Blade-type multi-fused circuits

●  ● 

Positive terminal battery covers

    ●   

JDLink

TM

 Ultimate wireless communication 

system with 3 years of service

 ▲

JDLink wireless communication system

   

 

●  ● 

Work lights: Halogen / One mounted on boom /

   

 

One mounted on frame

● 

▲ 

Optional equipment                                                            See your John Deere dealer for further information.

Customer Personal Service (CPS) is part of John Deere’s proactive, fix-before-fail strategy on machine
maintenance that will help control costs, increase profits, and reduce stress. Included in this compre-
hensive lineup of ongoing programs and services are:
 

Fluid analysis program – tells you what’s going on inside all of your machine’s major compo-

nents so you’ll know if there’s a problem before you see a decline in performance. Fluid analysis is
included in most extended coverage and preventive-maintenance agreements.
 

Component life-cycle data – gives you vital information on the projected life span of compo-

nents and lets you make informed decisions on machine maintenance by telling you approximately 
how many hours of use you can expect from an engine, transmission, or hydraulic pump. This infor-
mation can be used to preempt catastrophic downtime by servicing major components at about 80 
percent of their life cycle.
 

Preventive Maintenance (PM) agreements – give you a fixed cost for maintaining a machine

for a given period of time. They also help you avoid downtime by ensuring that critical maintenance

work gets done right and on schedule. On-site preventive maintenance service performed where 
and when you need it helps protect you from the expense of catastrophic failures and lets you avoid 
waste-disposal hassles.
 

Extended coverage – gives you a fixed cost for machine repairs for a given period of time so

you can effectively manage costs. Whether you work in a severe-service setting or just want to spread
the risk of doing business, this is a great way to custom-fit coverage for your operation. And an 
extended coverage contract also travels well because it’s backed by John Deere and is honored by 
all Deere construction dealers.
 

Customer Support Advisors (CSAs) – Deere believes the CSA program lends a personal quality

to Customer Personal Service (CPS). Certified CSAs have the knowledge and skills for helping make 
important decisions on machine maintenance and repair. Their mission is to help you implement a 
plan that’s right for your business and take the burden of machine maintenance off your shoulders.

Cyan 

Magenta 

Yellow 

Black 

DKAX135D225D Page 24