Snapper 281222BE 사용자 설명서
25
Section 4 - ADJUSTMENTS & REPAIR
WARNING
DO NOT attempt any adjustments, maintenance,
service or repairs with the engine running. Stop
engine. Stop blade. Engage parking brake. Remove
key. Remove spark plug wire from spark plug and
secure away from plug. Engine and components are
HOT. Avoid serious burns, allow all parts to cool
before working on machine. Fuel Filler Cap and Vent
must be closed securely to prevent fuel spillage. DO
NOT attempt to service or charge the battery while it
is installed on the machine.
service or repairs with the engine running. Stop
engine. Stop blade. Engage parking brake. Remove
key. Remove spark plug wire from spark plug and
secure away from plug. Engine and components are
HOT. Avoid serious burns, allow all parts to cool
before working on machine. Fuel Filler Cap and Vent
must be closed securely to prevent fuel spillage. DO
NOT attempt to service or charge the battery while it
is installed on the machine.
4.6 BATTERY
4.6.1. BATTERY REMOVAL
1. Carefully pull each side of battery cover away
from ratchet fasteners and remove cover. See
Figure 4.17.
1. Carefully pull each side of battery cover away
from ratchet fasteners and remove cover. See
Figure 4.17.
FIGURE 4.17
2. Remove the hair pin and swivel from the deck
support to allow clearance for battery removal.
3. Slide battery from battery box to gain access to
terminal cables.
4. Observe and note cable positions on battery.
See Figure 4.18.
5.
support to allow clearance for battery removal.
3. Slide battery from battery box to gain access to
terminal cables.
4. Observe and note cable positions on battery.
See Figure 4.18.
5.
Disconnect cables from battery terminals,
disconnecting BLACK (Negative) cable first. Retain
mounting bolts and nuts.
mounting bolts and nuts.
CAUTION
If battery is removed, DO NOT operate engine
without insulating Positive + battery cable terminal
with electrical tape, or sparking from battery cables
can result.
without insulating Positive + battery cable terminal
with electrical tape, or sparking from battery cables
can result.
FIGURE 4.18
WARNING
Cables must be connected to battery terminals in the
proper position as show in Figure . DO NOT attempt
to charge battery while installed on the Rear Engine
Rider. DO NOT use “BOOST” chargers on the
battery.
proper position as show in Figure . DO NOT attempt
to charge battery while installed on the Rear Engine
Rider. DO NOT use “BOOST” chargers on the
battery.
4.6.2. BATTERY
INSTALLATION
1. Slide battery partially into battery housing.
2. Connect positive (+) cable (red) first, from
wiring harness to the positive terminal (+) on
battery using bolt and nut provided in hardware
bag. Connect negative (-) cable (black) last, to
negative terminal (-) on battery using bolt and nut.
Apply a small amount of grease over terminals to
prevent corrosion.
3. Reinstall positive terminal insulator.
4. Insert battery completely into battery housing.
5. Reinstall battery cover. See Figure 4.17.
6. Reinstall swivel and hair pin for deck support.
2. Connect positive (+) cable (red) first, from
wiring harness to the positive terminal (+) on
battery using bolt and nut provided in hardware
bag. Connect negative (-) cable (black) last, to
negative terminal (-) on battery using bolt and nut.
Apply a small amount of grease over terminals to
prevent corrosion.
3. Reinstall positive terminal insulator.
4. Insert battery completely into battery housing.
5. Reinstall battery cover. See Figure 4.17.
6. Reinstall swivel and hair pin for deck support.
BATTERY COVER
RATCHET
FASTENERS
FASTENERS
BLACK
NEGATIVE (-)
CABLE
NEGATIVE (-)
CABLE
RED
POSITIVE (+)
CABLE
POSITIVE (+)
CABLE
POSITIVE TERMINAL
INSULATOR
INSULATOR
INSTALL BATTERY POSITIVE
(+) END FIRST INTO
BATTERY COMPARTMENT IN
DIRECTION OF ARROW AS
SHOWN
(+) END FIRST INTO
BATTERY COMPARTMENT IN
DIRECTION OF ARROW AS
SHOWN