Snapper Rear Engine Riders 사용자 설명서
6
DEALER PRE-SALE CHECKLIST
The following must be accomplished prior sale. Refer to detailed set-up instructions. Review this list with
purchaser. Check (
purchaser. Check (
✓
) items actually performed and signed on this page.
SET-UP CHECKLIST
______ STEERING WHEEL and steering shaft assembled.
______ TIE RODS connected.
______ LUBRICATION of entire unit completed.
______ OPERATOR’S SEAT installed and tightened and seat switch connected.
______ FUEL TANK installed and fuel line connected.
______ GRASS DEFLECTOR, MULCH COVER or CATCHER ADAPTER and assembly positioned, secured, checked.
______ BATTERY activated and charge per instructions and installed into battery compartment on rider.
______ TIRE inflated to proper Pounds per Square Inch (PSI). Front tire is 15 PSI and Rear tire is 10 PSI.
______ TIE RODS connected.
______ LUBRICATION of entire unit completed.
______ OPERATOR’S SEAT installed and tightened and seat switch connected.
______ FUEL TANK installed and fuel line connected.
______ GRASS DEFLECTOR, MULCH COVER or CATCHER ADAPTER and assembly positioned, secured, checked.
______ BATTERY activated and charge per instructions and installed into battery compartment on rider.
______ TIRE inflated to proper Pounds per Square Inch (PSI). Front tire is 15 PSI and Rear tire is 10 PSI.
CUTTING BLADE & MOWER
______ BLADE RETAINING hardware checked for proper tightness.
______ BLADE TIP CLEARANCE inside lower edge of mower checked and corrected as needed.
______ BLADE STRAIGHTNESS checked and adjusted as required.
______ MOWER CUTTING HEIGHT settings checked and adjusted as needed (with tires properly inflated).
______ MOWER SIDE TO SIDE level checked and adjusted as needed (with tires properly inflated).
______ MOWER FRONT TO REAR setting checked and adjusted as needed (with tires properly inflated).
______ BLADE LEVER checked and adjusted as required.
______ BELT TENSION checked and adjusted as required. (25” Decks Only)
______ BLADE TIP CLEARANCE inside lower edge of mower checked and corrected as needed.
______ BLADE STRAIGHTNESS checked and adjusted as required.
______ MOWER CUTTING HEIGHT settings checked and adjusted as needed (with tires properly inflated).
______ MOWER SIDE TO SIDE level checked and adjusted as needed (with tires properly inflated).
______ MOWER FRONT TO REAR setting checked and adjusted as needed (with tires properly inflated).
______ BLADE LEVER checked and adjusted as required.
______ BELT TENSION checked and adjusted as required. (25” Decks Only)
PRE-START CHECKS & SERVICES
______ TIRES checked and inflated to correct pressures.
______ ENGINE OIL level checked.
______ DIFFERENTIAL check lubricant and add as needed.
______ CHAIN CASE check lubricant and add as needed.
______ YOKE ASSEMBLY checked for freedom of movement.
______ FUEL added to tank and system checked for leaks. Refer to Engine’s Owner’s Manual for fuel specifications.
______ BATTERY (not overfilled!) reinstalled and properly connected with red boot over positive terminal.
______ ENGINE OIL level checked.
______ DIFFERENTIAL check lubricant and add as needed.
______ CHAIN CASE check lubricant and add as needed.
______ YOKE ASSEMBLY checked for freedom of movement.
______ FUEL added to tank and system checked for leaks. Refer to Engine’s Owner’s Manual for fuel specifications.
______ BATTERY (not overfilled!) reinstalled and properly connected with red boot over positive terminal.
OPERATIONAL TESTS
______ CHECK SEAT SWITCH for proper function
______ INTERLOCK SYSTEMS checked to insure proper functioning.
______ ENGINE STARTED and throttle control settings checked.
______ IGNITION SWITCH checked to insure engine stops when turned to OFF position.
______ PARKING BRAKE tested to insure proper operation.
______ CLUTCH/BRAKE tested for proper operation and adjusted as required.
______ BLADE STOPS in 3 seconds or less after releasing the blade pedal. Adjust blade brake as required.
______ BLADE LEVER can be moved to “OFF” position with blade pedal depressed.
______ INTERLOCK SYSTEMS checked to insure proper functioning.
______ ENGINE STARTED and throttle control settings checked.
______ IGNITION SWITCH checked to insure engine stops when turned to OFF position.
______ PARKING BRAKE tested to insure proper operation.
______ CLUTCH/BRAKE tested for proper operation and adjusted as required.
______ BLADE STOPS in 3 seconds or less after releasing the blade pedal. Adjust blade brake as required.
______ BLADE LEVER can be moved to “OFF” position with blade pedal depressed.
DEMONSTRATION & INSTRUCTION
______ DEMONSTRATED proper operation of mower to purchaser.
______ INSTRUCTED purchaser to read and follow instructions in Operator's Manual.
______ PERSONALLY HANDED Operator's Manual, Engine Manual, and “USER and SAFETY GUIDE” video to purchaser.
______ ASSISTED purchaser in completing Product Registration cards.
______ INSTRUCTED purchaser to read and follow instructions in Operator's Manual.
______ PERSONALLY HANDED Operator's Manual, Engine Manual, and “USER and SAFETY GUIDE” video to purchaser.
______ ASSISTED purchaser in completing Product Registration cards.
DEALER'S RECORDS
SALE DATE
RIDER MODEL
SERIAL NO.
Dealer's Name
Signature
Address _________________________ City
State
Zip
TRACTOR WILL BE USED COMMERCIALLY? YES _________ NO
Purchaser's Name
Signature
Address _________________________ City
State
Zip
IMPORTANT: This form is to be retained by the Dealer for future reference regarding Warranty, proof of purchase,
traceability for product recall or service, etc. Complete the Product Registration Card immediately and mail to: Customer
Service Department at SNAPPER, P.O. BOX 1379, McDonough, Georgia, 30253.
traceability for product recall or service, etc. Complete the Product Registration Card immediately and mail to: Customer
Service Department at SNAPPER, P.O. BOX 1379, McDonough, Georgia, 30253.
INSTRUCTION No. 3-5621 (REV. 3, 8/20/99)