Troy-Bilt N779Pony 사용자 설명서
15
•
Release the parking brake by depressing the
clutch-brake pedal and positioning the speed
control lever in desired position.
clutch-brake pedal and positioning the speed
control lever in desired position.
IMPORTANT:
First-time operators should use speed
positions 1 or 2. Become completely familiar with the
tractor’s operation and controls before operating the
tractor in higher speed positions.
tractor’s operation and controls before operating the
tractor in higher speed positions.
•
Release clutch-brake pedal slowly to put unit into
motion.
motion.
•
The lawn tractor is brought to a stop by depressing
the clutch-brake pedal.
the clutch-brake pedal.
NOTE:
When operating the unit initially, there will be
little difference between the highest two speeds until
after the belts have seated themselves into the pulleys
during the break-in period.
after the belts have seated themselves into the pulleys
during the break-in period.
WARNING:
Before leaving the operator’s
position for any reason, disengage the
blades, place the shift lever in neutral,
engage the parking brake, shut engine off
and remove the key.
blades, place the shift lever in neutral,
engage the parking brake, shut engine off
and remove the key.
IMPORTANT:
When stopping the tractor for any reason
while on a grass surface, always
•
Place the shift lever in neutral,
•
Engage the parking brake,
•
Shut engine off and remove the key.
Doing so will minimize the possibility of having your
lawn ‘‘browned’’ by hot exhaust from your tractor’s
running engine.
lawn ‘‘browned’’ by hot exhaust from your tractor’s
running engine.
If unit stalls with speed control in high speed, or if unit
will not operate with speed control lever in a low speed
position, proceed as follows.
will not operate with speed control lever in a low speed
position, proceed as follows.
•
Place shift lever in NEUTRAL.
•
Restart engine.
•
Place speed control lever in highest speed position.
•
Release clutch-brake pedal fully.
•
Depress clutch-brake pedal.
•
Place speed control lever in desired position.
•
Place shift lever in either FORWARD or REVERSE,
and follow normal operating procedures.
and follow normal operating procedures.
Driving On Slopes
Refer to the SLOPE GAUGE on page 7 to help determine
slopes where you may operate the tractor safely.
slopes where you may operate the tractor safely.
WARNING:
Do not mow on inclines with a
slope in excess of 15 degrees (a rise of
approximately 2-1/2 feet every 10 feet). The
tractor could overturn and cause serious
injury.
approximately 2-1/2 feet every 10 feet). The
tractor could overturn and cause serious
injury.
•
Mow up and down slopes, NEVER across.
•
Exercise extreme caution when changing direction
on slopes.
on slopes.
•
Watch for holes, ruts, bumps, rocks, or other
hidden objects. Uneven terrain could overturn the
machine. Tall grass can hide obstacles.
hidden objects. Uneven terrain could overturn the
machine. Tall grass can hide obstacles.
•
Avoid turns when driving on a slope. If a turn must
be made, turn down the slope. Turning up a slope
greatly increases the chance of a roll over.
be made, turn down the slope. Turning up a slope
greatly increases the chance of a roll over.
•
Avoid stopping when driving up a slope. If it is
necessary to stop while driving up a slope, start up
smoothly and carefully to reduce the possibility of
flipping the tractor over backward.
necessary to stop while driving up a slope, start up
smoothly and carefully to reduce the possibility of
flipping the tractor over backward.
Using the Deck Lift Lever
To raise the cutting deck, move the deck lift lever to the
left, then place it in the notch best suited for your
application. Refer to Setting The Cutting Height earlier in
this section.
left, then place it in the notch best suited for your
application. Refer to Setting The Cutting Height earlier in
this section.
Engaging the Blades
Engaging the PTO (Blade Engage) transfers power to
the cutting deck or other (separately available)
attachments. To engage the blades, proceed as
follows:
the cutting deck or other (separately available)
attachments. To engage the blades, proceed as
follows:
•
Move the throttle control lever to the FAST (rabbit)
position.
position.
•
Grasp the PTO (Blade Engage) lever and position it
all the way forward into the engaged (ON) position.
all the way forward into the engaged (ON) position.
•
Keep the throttle lever in the FAST (rabbit) position
for the most efficient use of the cutting deck or other
(separately available) attachments
for the most efficient use of the cutting deck or other
(separately available) attachments
IMPORTANT:
The engine will automatically shut off if the
PTO is engaged with the shift lever in position for
reverse travel with the ignition key in the NORMAL
MOWING position. Refer to Safety Interlock Switches on
page 13.
reverse travel with the ignition key in the NORMAL
MOWING position. Refer to Safety Interlock Switches on
page 13.