Roland XV-3080 사용자 설명서
140
Chapter 9 Examples of Applications Using the XV-3080
Controlling the TMT with the
LFO and Changing the
Tone’s Cycle Time
LFO and Changing the
Tone’s Cycle Time
When TMT (Tone Mix Table) is selected as the Matrix
Control destination, you can use the Control Source
controller to change the time at which Tones in a Patch are
played.
Control destination, you can use the Control Source
controller to change the time at which Tones in a Patch are
played.
fig.9-01
Here is an example of a Patch using LFO1 as a Control
Source. The time at which the Tone is played is based on the
LFO1’s amplitude value.
Source. The time at which the Tone is played is based on the
LFO1’s amplitude value.
1. Select “PR-E:043 Morph Pad” on the PATCH PLAY page.
86), set the Lower and Upper Velocity Range values for
Tones 1 and 2.
Tones 1 and 2.
the Velocity Range settings of four Tones in one screen,
making it easier to adjust these settings.
making it easier to adjust these settings.
Set the Velocity Range for both of the tones as follows.
L
:
U
tone = 1
1
: 64
tone = 2
65 : 127
3. In the TMT VEL RANGE page (PATCH-COMMON, set
the Velocity Fade L.Fade and U.Fade settings to 10 for
Tones 1 and 2.
Tones 1 and 2.
This makes the Tones fade in and out smoothly outside their
velocity ranges.
velocity ranges.
4. On the TMT VELO CONTROL page (PATCH-
COMMON), set the TMT Velocity Control to OFF.
This setting disables the Velocity Range settings made in
Step 2 and causes the two Tones to sound simultaneously,
regardless of the velocity – the force with which keys are
played – received from your MIDI keyboard or sequencer.
Step 2 and causes the two Tones to sound simultaneously,
regardless of the velocity – the force with which keys are
played – received from your MIDI keyboard or sequencer.
TMT Ctrl Sw to ON.
This setting allows the TMT to be controlled by the Matrix
Control Controller. The following chart shows all the
relationships between the TMT Velocity Control and TMT
Ctrl Sw.
Control Controller. The following chart shows all the
relationships between the TMT Velocity Control and TMT
Ctrl Sw.
(1)
(2)
(3)
(4)
[TMT Velocity Control] ON OFF ON OFF
[TMT Ctrl Sw]
OFF OFF ON ON
(1)(3): The Velocity Control settings are enabled, and the two
Tones are switched on or off according to the velocity data
received from the MIDI keyboard or sequencer.
Tones are switched on or off according to the velocity data
received from the MIDI keyboard or sequencer.
(2): The Velocity Control settings and TMT control by Matrix
Control are disabled, and the two Tones play
simultaneously, regardless of the velocity data received from
the MIDI keyboard or sequencer.
simultaneously, regardless of the velocity data received from
the MIDI keyboard or sequencer.
(4): TMT Matrix Control is enabled, and the timing of the
Tones changes according to the Control Source controller
data.
Tones changes according to the Control Source controller
data.
* The TMT Velocity Control settings are given priority when
both TMT Velocity Control and TMT Ctrl Sw are set to ON.
6. Select LFO1 as the Control1 source in the MATRIX CTRL
7. In the MATRIX CONTROL1 page (PATCH-CONTROL),
set DEST1 as shown below.
Dest:
TMT
Sns:
+63
Tone:
o o _ _ (applied to Tone 1 and 2)
8. In each Tone’s LFO1 WAVE page (PATCH-CONTROL),
set the Form and Rate for each of the Tones as shown
below.
below.
tone=1
tone=2
Form:
SIN
SIN
Rate:
64
127
9. Select the Number for Tones 1 and 2 on the WAVE page
for four Tones in one window, making it easier to make these
settings.
settings.
10. Press [EXIT] to return to the PATCH PLAY page.
Other possible applications include synchronizing the
Control Source LFO rate to the tempo, assigning Modulation
and other parameters to the Control Source, and changing
the Tone in realtime from a MIDI keyboard or other such
device.
Control Source LFO rate to the tempo, assigning Modulation
and other parameters to the Control Source, and changing
the Tone in realtime from a MIDI keyboard or other such
device.