Roland XV-3080 사용자 설명서
27
Chapter 2 Using the XV-3080 Effects
Chapter 2
Adjusting Multi-Effects Settings
PERFORM MFX TYPE
Type (MFX Type)
Use this parameter to select from among the 63 available
Multi-Effects. For a description of these effects, check out
“Parameters for Each Multi-Effect (MFX TYPE)” (p. 36).
Multi-Effects. For a description of these effects, check out
“Parameters for Each Multi-Effect (MFX TYPE)” (p. 36).
Source (MFX Source)
Select the MFX parameter settings that will be used by the
Performance. If you wish to use the MFX parameter settings
of the Performance, select PERFORM. If you wish to use the
MFX parameter settings of the Patch assigned to one of the
Parts, select the Part number.
Performance. If you wish to use the MFX parameter settings
of the Performance, select PERFORM. If you wish to use the
MFX parameter settings of the Patch assigned to one of the
Parts, select the Part number.
PERFORM MFX PRM
These parameters allow you to customize the selected Multi-
Effect. For a description of the parameters, check out
“Parameters for Each Multi-Effect (MFX TYPE)” (p. 36).
Effect. For a description of the parameters, check out
“Parameters for Each Multi-Effect (MFX TYPE)” (p. 36).
* You cannot select this page when “Type” on the PERFORM
MFX TYPE page is set to THROUGH.
PERFORM MFX CTRL
Select the Control Source to be used for changing the Multi-
Effects parameters, and set the Sens and parameters to be
changed by that Control Source.
Effects parameters, and set the Sens and parameters to be
changed by that Control Source.
* You cannot select this page when “Type” on the PERFORM
MFX TYPE page is set to THROUGH.
Control 1–4 (MFX Control 1–4 Source)
OFF:
No controller is used.
CC01–95:
Controller numbers 1–95 (except for 32)
BENDER:
Pitch Bend
AFTERTOUCH:
Aftertouch
SYS-CTRL 1–4:
System control (Control 1–4)
Destination
This selects the Multi-Effects parameter to be controlled
using the MFX Control 1–4 source.
using the MFX Control 1–4 source.
Sens (MFX Control Sens) -63– +63
If you wish to modify the selected parameter in a positive (+)
direction – i.e., a higher value, toward the right, or faster etc.
– from its current setting, select a positive (+) value. If you
wish to modify the selected parameter in a negative (-)
direction – i.e., a lower value, toward the left, or slower etc. –
from its current setting, select a negative (-) value. Higher
numbers produce a greater amount of change.
direction – i.e., a higher value, toward the right, or faster etc.
– from its current setting, select a positive (+) value. If you
wish to modify the selected parameter in a negative (-)
direction – i.e., a lower value, toward the left, or slower etc. –
from its current setting, select a negative (-) value. Higher
numbers produce a greater amount of change.
PERFORM MFX OUT
These parameters allow you to route the output of the Multi-
Effects to the desired OUTPUT jacks, and to set the final level
of the Multi-Effects.
Effects to the desired OUTPUT jacks, and to set the final level
of the Multi-Effects.
Output (MFX Output Assign) A/B/C
This selects the pair of OUTPUT jacks to which the Multi-
Effects stereo output is routed.
Effects stereo output is routed.
Dry (MFX Dry Send Level) 0–127
This sets the Multi-Effects unit’s output level to the selected
OUTPUT jacks.
OUTPUT jacks.
Chorus (MFX Chorus Send Level) 0–127
This sets the amount of the Multi-Effects output to be sent to
the Chorus.
the Chorus.
Reverb (MFX Reverb Send Level) 0–127
This sets the amount of the Multi-Effects output to be sent to
the Reverb.
the Reverb.