Roland XV-3080 사용자 설명서
76
Chapter 3 Selecting Output Jacks
PERFORM CHO OUT ([PERFORM]-
[EFFECTS])
[EFFECTS])
Output Assign (Chorus Output Assign) A/B/C
This setting selects the pair of OUTPUT jacks to which the
Chorus unit’s stereo output is routed when Chorus Output
Select is set to “MAIN” or “MAIN+R.”
Chorus unit’s stereo output is routed when Chorus Output
Select is set to “MAIN” or “MAIN+R.”
Level (Chorus Level) 0–127
This setting determines the Chorus output level.
Select (Chorus Output Select)
This parameter allows you to send the Chorus output
directly to the currently selected OUTPUT jacks, to the
Reverb, or to both.
directly to the currently selected OUTPUT jacks, to the
Reverb, or to both.
MAIN:
The Chorus output is sent only to the OUTPUT jacks.
REV:
The Chorus output is sent only to the Reverb.
MAIN+R:
The Chorus output is sent to the OUTPUT jacks
and to the Reverb.
PERFORM REV OUT ([PERFORM]-
[EFFECTS])
[EFFECTS])
Output Assign (Reverb Output Assign) A/B/C
This specifies the OUTPUT jacks to which the Reverb unit’s
stereo output is routed.
stereo output is routed.
Level (Reverb Level) 0–127
This setting determines the Reverb output level.
SYSTEM SETUP ([SYSTEM]-[COMMON])
Master Level 0–127
This adjusts the volume of the entire XV-3080.
Mix/Parallel
MIX:
All Parts – including those routed to OUTPUTs B/C or
INDIVIDUAL 3–6 – are mixed together and routed to the
A(MIX) OUTPUT jacks.
A(MIX) OUTPUT jacks.
This setting allows you to quickly route everything through
headphones when you are creating sounds, or to combine all
of your sounds into two outputs when sending the XV-3080’s
signal to a mixer that has only two channels.
headphones when you are creating sounds, or to combine all
of your sounds into two outputs when sending the XV-3080’s
signal to a mixer that has only two channels.
* When MIX is selected, sounds routed to the INDIVIDUAL 3/
5 jacks are sent to the left A(MIX) OUTPUT jack, and sounds
routed to the INDIVIDUAL 4/6 jacks are sent to the right
A(MIX) OUTPUT jack.
routed to the INDIVIDUAL 4/6 jacks are sent to the right
A(MIX) OUTPUT jack.
PARALLEL:
Sounds are routed to output jacks according to
their output settings.
* The XV-3080’s Master Level and Mix/Parallel settings are
each established using a single global parameter.
Example of Settings
Selecting Different Output Destinations
for Parts in a Performance
for Parts in a Performance
This example describes the procedure for outputting Part 1
from the A(MIX) OUTPUT jacks without sending it through
any internal effects, sending Part 2 through the Multi-Effects
and then outputting it from the B OUTPUT jack, and
outputting Part 3 from the INDIVIDUAL 5 OUTPUT jack
without sending it through any internal effects.
from the A(MIX) OUTPUT jacks without sending it through
any internal effects, sending Part 2 through the Multi-Effects
and then outputting it from the B OUTPUT jack, and
outputting Part 3 from the INDIVIDUAL 5 OUTPUT jack
without sending it through any internal effects.
First, set Part 1.
1. Select the Performance you wish to use.
2. Press [EFFECTS] so that its indicator lights.
3. Press [
] / [
] to select the PART OUTPUT page.
4. Press PART SELECT [1/9] to make its indicator light.
* Make sure that the [1-8/9-16] button’s indicator is not lit. If
the indicator is lit, press [1-8/9-16] to turn it off.
5. Press [
] / [
] to move the cursor to Output
Assign.
6. Turn the VALUE dial or press [INC] / [DEC] to select
OUTPUT A.
7. Press [
] / [
] to move the cursor to Chorus.
8. Turn the VALUE dial to select 0.
9. Set the Part’s Reverb send to 0 by repeating Steps 7 and 8,
selecting Reverb in Step 7.
Next, set up Part 2.
1. Press PART SELECT [2/10] to make its indicator light.