Roland 04672434 사용자 설명서
137
MASTER Chapter 8 Parameter Guide
Chapter 8
FILTER
This passes only portions of the sound’s frequency ranges, giving the
sound a unique tone. You can add different types of expression to
the sound by changing the frequencies (pitches) that are passed.
sound a unique tone. You can add different types of expression to
the sound by changing the frequencies (pitches) that are passed.
ASSIGNABLE
*1
Setting available with SOURCE set to D BEAM V.
Parameter/
Range
Range
Explanation
FREEZE CH (Freeze Channel)
This selects the channel to which the FREEZE effect is applied.
A
FREEZE is applied only to Channel A.
B
FREEZE is applied only to Channel B.
A+B
FREEZE is applied to both Channel A and B.
ATTACK
0–100
This sets the attack time for the FREEZE
sound when FREEZE is switched on. Rais-
ing the value increases the attack time.
sound when FREEZE is switched on. Rais-
ing the value increases the attack time.
REL (Release)
0–100
This sets the time for the FREEZE sound to
be released when FREEZE is switched off.
Raising the value increases the release time.
be released when FREEZE is switched off.
Raising the value increases the release time.
LEVEL
0–100
This sets the volume level of the freeze
sound. The volume increases as the value is
raised.
sound. The volume increases as the value is
raised.
DIRECT
0–100
This sets the volume level of the direct
sound. The volume increases as the value is
raised.
sound. The volume increases as the value is
raised.
Parameter/
Range
Range
Explanation
FILTER CH (Filter Channel)
This selects the channel to which the filter is applied.
A
The filter is applied only to Channel A.
B
The filter is applied only to Channel B.
A+B
The filter is applied to both Channel A and B.
TYPE
This selects the filter type.
LPF
This filter passes only the low frequencies.
BPF
This filter passes frequencies only in the
specified range.
specified range.
HPF
This filter passes only the high frequencies.
FREQ MIN (Frequency Minimum)
0–100
This sets the frequency when the filter is
first activated. Higher frequencies are set as
the value is raised.
first activated. Higher frequencies are set as
the value is raised.
FREQ MAX (Frequency Maximum)
0–100
This sets the frequency when the filter is
most fully applied (the maximum value).
Higher frequencies are set as the value is
raised.
most fully applied (the maximum value).
Higher frequencies are set as the value is
raised.
RESO (Resonance)
0–100
Adjusts the amount of filter resonance (dis-
tinctiveness of the sound) used. Raising the
value strengthens the characteristic coloring
of the tone.
tinctiveness of the sound) used. Raising the
value strengthens the characteristic coloring
of the tone.
LEVEL
0–100
Adjusts the volume level. Raising the value
increases the volume.
increases the volume.
Parameter/
Range
Range
Explanation
SW
OFF, ON
This setting switches D BEAM ASSIGN-
ABLE on and off.
ABLE on and off.
TARGET PARAMETER
This selects the parameter to be changed.
MIN (Minimum)
This sets the minimum value for the range in which the parameter
can change.
The value differs depending on the parameter assigned for TARGET
PARAMETER.
can change.
The value differs depending on the parameter assigned for TARGET
PARAMETER.
MAX (Maximum)
This sets the maximum value for the range in which the parameter
can change.
The value differs depending on the parameter assigned for TARGET
PARAMETER.
can change.
The value differs depending on the parameter assigned for TARGET
PARAMETER.
SW MODE (Switch Mode) *1
This sets the behavior of the value each time the switch is operated.
MOMENT
The setting is normally OFF (minimum val-
ue), switching to ON (maximum value)
while the CONTROL button is held down.
ue), switching to ON (maximum value)
while the CONTROL button is held down.
LATCH
The setting alternately switches to OFF
(minimum value) and ON (maximum val-
ue) each time the CONTROL button is
pressed.
(minimum value) and ON (maximum val-
ue) each time the CONTROL button is
pressed.
RANGE LOW, RANGE HIGH
Low: 0–126
High: 1–127
High: 1–127
You can set the range for control of target
parameters within the D BEAM controller’s
response range. Target parameters are
controlled within the range set with
RANGE LOW and RANGE HIGH. You
should normally set RANGE LOW to 0 and
RANGE HIGH to 127.
parameters within the D BEAM controller’s
response range. Target parameters are
controlled within the range set with
RANGE LOW and RANGE HIGH. You
should normally set RANGE LOW to 0 and
RANGE HIGH to 127.
Parameter/
Range
Range
Explanation
VB-99_e.book 137 ページ ２００８年８月１８日 月曜日 午後１時１０分