Korg 2E ii 사용자 설명서

• Is the SD card set to the “protected” setting?

Turn off the write protect switch, insert the card 
back into the slot, and perform the save or load 
operation once again. ........................................

• Is the EXB-SMPL installed correctly? .......

• Is the EXB-SMPL installed correctly? .......

• Is your audio source connected to the AUDIO 

INPUT 1, 2 jacks? .................................................

• Is the [LEVEL] knob raised?...............................

• Is the [MIC/LINE] switch set appropriately? 

• If there is no sound in Sampling mode, go to SMPL 

1.1: Recording, select the Input/Pref page, and 
make sure that “Lvl” and “BUS” are set correctly. 

................................................................

• If there is no sound in Program, Combination, or 

Sequencer modes, go to GLOBAL 1.1: System, 
select the Audio In page, and make sure that 
“Input1 Level,” “Input1 BUS Select,” “Input2 
Level” and “Input2 BUS Select” are set correctly.

............................................................

• If sound is still not input even after you have set 

“Input 1 Level,” “Input 2 BUS Select,” “Input 2 
Level,” and “Input 2 BUS Select” in the GLOBAL 
1.1: System, Audio In page, temporarily lower the 
“Input 1 Level” and “Input 2 Level,” and then 
move to Program, Combination, or Sequencer 
mode. Turn return to Global mode, and make the 
settings once again. ...........................................

• Are one or more SIMM modules installed?

........................................................................

• Is there free memory area?.........................

Select a different memory bank...................

Delete unneeded samples.............................

Save important samples before deleting them. 

..................................................................

• If you are able to switch the mode setting of your 

MO drive between DOS/V(PC/AT) and Mac 
settings, please use DOS/V(PC/AT) mode. For 
details on changing the mode of your drive, refer to 
the owner’s manual for your MO drive.

• Use the Media mode Media Information page 

utility “Scan SCSI device” to remount the SCSI 
device.

• If your MO drive does not have a mode setting, or 

if the media exchange is not recognized even after 
you switch the mode, use the drive select button to 
select a different drive, and then re-select the MO 
drive.

• Is the USB cable connected correctly?

• Is the CD-ROM inserted in your CD drive?

Make sure that the CD-ROM is inserted correctly.

• Could the lens of your CD drive be dirty?

Use a commercially-available lens cleaner to clean 
the lens.

• Are you attempting to install from a network CD 

drive?
This software cannot be installed from a network-
connected CD drive.

• Are you able to use USB?

If you are using Windows XP, go to [Control Panel] 

→ [System], and select the [Hardware] tab. In 
[Device Manager], check the settings for Universal 
Serial Bus Controller and USB Root Hub.

• Has the TR been detected as an unknown device?

If you are using Windows XP, go to [Control Panel] 

→ [System], select the [Hardware] tab, and check 
[Device Manager]. If the TR has not been detected 
correctly, it will be displayed in “Other devices” or 
“Unknown devices.” Reconnect the USB cable; if 
the TR is again displayed as an “Unknown device,” 
the computer has failed to detect it correctly. Delete 
the “Unknown device” entry, and reinstall the 
driver. ...........................................................

• Is the USB cable connected correctly?

• Did you install the driver?

• Has your computer detected the connected TR?

If you are using Windows XP, go to Control Panel 

→ “Sounds and Audio Devices Properties” and 
click the Hardware tab.

If you are using Mac OS X, go to Macintosh HD 

→ 

Application folder 

→ Utility folder → “Audio MIDI 

Settings,” select the “MIDI Devices” tab, and check 
that the TR has been detected.

Some computers may not recognize the TR 
because of their hardware configuration.

• Check the TR’s assignments and USB-MIDI port 

settings.

• The connected device or software may not support 

the messages you are transmitting. Refer to the 
owner’s manual of the connected device or 
software to verify that it responds to the messages 
you are transmitting.