Poulan PRRT850 사용자 설명서

OPERATION

OIL

LEVEL

FIG. 12

BEFORE START ING ENGINE

IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT

TO ENTER THE ENGINE WHEN CHECKING OR ADDING

OIL OR FUEL. USE CLEAN OIL AND FUEL AND STORE IN

APPROVED, CLEAN, COVERED CONTAINERS. USE CLEAN

FILL FUNNELS.

CHECK ENGINE OIL LEVEL (See Fig. 12)

• The engine in your unit has been shipped, from the

factory, already filled with SAE 30 summer weight oil.

•

With engine level, clean area around oil filler plug and

remove plug.

•

Engine oil should be to point of overflowing when engine

is level. For ap proxi mate capacity see “PROD UCT

SPEC I FI CA TIONS” on page 3 of this manual. All oil

must meet A.P.I. Service Classification SF-SJ.

• Reinstall engine oil cap and tighten.
• For cold weather operation you should change oil for

easier starting (See oil viscosity chart in the Mainte-

nance sec tion of this manual).

• To change engine oil, see the Maintenance section in

this manual.

ADD GASOLINE

• Fill fuel tank to bottom of filler neck. Do not overfill.

Use fresh, clean, regular un lead ed gasoline with a

minimum of 87 octane. (Use of leaded gasoline will

increase carbon and lead oxide deposits and reduce

valve life). Do not mix oil with gasoline. Purchase fuel

in quan ti ties that can be used within 30 days to assure

fuel freshness.

CAUTION: Fill to within 1/2 inch of top

of fuel tank to prevent spills and to allow

for fuel expansion. If gasoline is ac-

ci den tal ly spilled, move machine away

from area of spill. Avoid creating any

source of ignition until gasoline vapors

have disappeared.
Wipe off any spilled oil or fuel. Do not

store, spill or use gasoline near an

open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES

BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE

GAS O LINE TO HELP INSURE GOOD COLD WEATHER

START ING.

CAUTION: Alcohol blended fuels (called

gas o hol or using ethanol or methanol) can at-

tract moisture which leads to sep a ra tion and

for ma tion of acids during storage. Acidic gas

can damage the fuel system of an engine while

in storage. To avoid engine problems, the fuel

system should be emptied before stor age of

30 days or longer. Drain the gas tank, start

the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel next

sea son. See Storage In struc tions for additional

information. Never use engine or carburetor

cleaner products in the fuel tank or permanent

damage may occur.

• Swing the handle in the opposite direction you wish

to turn, being careful to keep feet and legs away from

tines.

• When you have completed your turn-around, release

the drive control bar and lower handle. Place shift

lever in till position and move throttle control to de sired

speed. To begin tilling, hold drive control bar against

the handle.

OUTER SIDE SHIELDS (See Fig. 11)

The back edges of the outer side shields are slotted so

that the shields can be raised for deep tilling and low ered

for shal low tilling to protect small plants from being buried.

Loosen nut “A” in slot and nut “B”. Move shield to desired

position (both sides). Retighten nuts.

TO TRANSPORT

CAUTION: Before lifting or trans port ing,

allow tiller engine and muffler to cool.

Disconnect spark plug wire. Drain

gasoline from fuel tank.

AROUND THE YARD

• Release the depth stake pin. Move the depth stake

down to the top hole for transporting the tiller. Place

depth stake pin in hole of depth stake to lock in posi-

tion. This prevents tines from scuffing the ground.

• Place shift lever indicator in “F” (forward) position for

transporting.

• Hold the drive control bar against the handle to start

tiller movement. Tines will not turn.

• Move throttle control to desired speed.
AROUND TOWN

•  Disconnect spark plug wire.
•  Drain fuel tank.
•  Transport in upright position to prevent oil leakage.

TO START ENGINE (See Fig. 13)

CAUTION: Keep drive control bar in

“DISENGAGED” position when start-

ing en gine.

When starting engine for the first time or if engine has run

out of fuel, it will take extra pulls of the recoil starter to

move fuel from the tank to the engine.