Panasonic EY0005 사용자 설명서

1)

-This 

manual contains important safety and 
operating instructions for battery 
charger EY0005. 

2) Before using battery charger, read all 

instructions and cautionary markings 
on battery charger, battery pack, and 
product using battery pack. 

3)

-To reduce the 

risk of injury, charge only Panasonic 
Battery Pack as shown in last page. 

Other types of batteries may burst 
causing personal injury and damage.  

4) Do not expose charger to rain or snow. 

5) To reduce risk of damaging the electric 

plug and cord, pull by plug rather than 
cord when disconnecting charger. 

6) Make sure cord is Iocated so that it will 

not be stepped on, tripped over, or 
otherwise subjected to damage or 
stress. 

7) An extension cord should not be used 

unless absolutely necessary. 
Use of improper extension cord could 
result in a risk of fire and electric 
shock. If extension cord must be used, 
make sure that: 

a. pins on plug of extension cord are 

the same number, size and shape 
as those of plug on charger. 

b. extension cord is properly wired and 

in good electrical condition. 

c. wire size is large enough for ampere 

rating of charger as specified below. 

8) Do not operate charger with damaged 

cord or plug — replace them 
immediately. 

9) Do not operate charger if it has received 

a sharp blow, been dropped, or 
otherwise damaged in any way; take it 
to a qualified personnel. 

10) Do not disassemble charger; take it to 

a qualified personnel when service or 
repair is required. Incorrect reassembly 
may result in a risk of electric shock or 
fire. 

11) To reduce the risk of electric shock, 

unplug charger from outlet before 
attempting any maintenance or cleaning. 

12) The charger and battery pack are 

specifically designed to work together. 
Do not attempt to charge any other 
cordless tool or battery pack with this 
charger. 

13) Do not attempt to charge the battery 

pack with any other charger. 

14) Do not attempt to disassemble the 

battery pack housing. 

15) Do not store the tool and battery pack 

in locations where the temperature may 
reach or exceed 50

°C (122°F) (such a 

metal tool shed, or a car in the summer), 
which can lead to deterioration of the 
storage battery. 

16) Do not charge battery pack when the 

temperature is BELOW 0

°C (32°F) or 

ABOVE 40

°C (104°F). This is very 

important in order to maintain optimal 
condition of the battery pack. 

17) Do not incinerate the battery pack. 

It can explode in a fire. 

18) Avoid dangerous environment. Do not 

use charger in damp or wet locations. 

19) The charger is designed to operate on 

standard household electrical power 
only. Do not attempt to use it on any 
other voltage! 

20) Do not abuse cord. Never carry charger 

by cord or yank it to disconnect from 
outlet. Keep cord away from heat, oil 
and sharp edges. 

21) Charge the battery pack in a well 

ventilated place, do not cover the 
charger and battery pack with a cloth, 
etc., while charging. 

22) Use of an attachment not recommended 

may result in a risk of fire, electric shock, 
or injury to persons. 

23) Do not short the battery pack. A battery 

short can cause a large current flow, 
over heating and create the risk of fire 
or personal injury. 

24) NOTE: If the supply cord of this 

appliance is damaged, it must only be 
replaced by a repair shop authorized 
by the manufacturer, because special 
purpose tools are required. 

25) TO REDUCE THE RISK OF ELECTRIC 

SHOCK, THIS APPLIANCE HAS A 
POLARIZED PLUG (ONE BLADE IS 
WIDER THAN THE OTHER). 
This plug will fit in a polarized outlet 
only one way. If the plug does not fit 
fully in the outlet, reverse the plug. If it 
still does not fit, contact a qualified 
electrician to install the proper outlet. 
Do not change the plug in any way. 

• When you charge the battery pack for 

the first time, or after prolonged 
storage, charge it for about 24 hours 
to bring the battery up to full capacity. 

1. Plug the charger into the AC outlet. 

NOTE: 

• Sparks may be produced when the 

plug is inserted into the AC power 
supply, but this is not a problem in 
terms of safety.

2. Insert the battery pack firmly into the 

charger. 

3. During charging, the charging lamp will 

be lit. 
When charging is completed, an internal 
electronic switch will automatically be 
triggered to prevent overcharging. 
• Charging will not start if the battery 

pack is too warm (for example, 
immediately after heavy-duty operation). 
The charging lamp will be red flashing 
until the battery cools down. Charging 
will then begin automatically.

4. When charging is completed, the charging 

lamp will start flashing quickly. 

5. If the charging lamp does not light 

immediately after the charger is plugged 
in, or if after the standard charging time 
the lamp does not go off, consult an 
authorized dealer. 

RECOMMENDED MINIMUM AWG SIZE OF

EXTENSION CORDS FOR

BATTERY CHARGERS 

AC Input Rating.

Amperes

AWG Size of Cord

Equal to or

But less

Length of Cord, Feet

greater than

than

25 50 100 150

0

2

18 18

18

16

Battery pack

To AC

outlet

Battery charger

— 2 —

— 3 —

English

English

EY0005.qxd  04.6.22 9:24 AM  ページ 2