Pioneer PRO-101FD 사용자 설명서
45
En
05
Additional Picture Adjustment Options
5.6
Manage the Power
Your flat panel display is energy efficient but includes functions to save additional power. In an earlier section
entitled “4.2 Smart Starts for New Owners”, you were told how to activate the Energy Save feature. This section
provides more advanced functions to save power and to extend the panel life.
entitled “4.2 Smart Starts for New Owners”, you were told how to activate the Energy Save feature. This section
provides more advanced functions to save power and to extend the panel life.
AV Source - No Signal
To save energy and extend the life of your display, the panel can enter Standby automatically if the AV source
signal fails for 15 consecutive minutes. At five minutes before and at every minute after that, a warning message
appears on the screen. When the final minute elapses, the panel switches to Standby.
To have the panel switch to Standby when an AV source signal fails, follow the steps below.
To save energy and extend the life of your display, the panel can enter Standby automatically if the AV source
signal fails for 15 consecutive minutes. At five minutes before and at every minute after that, a warning message
appears on the screen. When the final minute elapses, the panel switches to Standby.
To have the panel switch to Standby when an AV source signal fails, follow the steps below.
1 ) Access No Signal Off through the Power Control menu.
2 ) Select
Enable to activate the AV Signal off power function.
3 ) Press HOME MENU to exit the menu.
AV Source - Non-Operational
To save energy, the panel can enter Standby automatically if there are no commands from the AV source for three
consecutive hours. At five minutes before and at every minute after that, a warning message appears on the
screen. When the final minute elapses, the panel switches to Standby.
To have the panel enter Standby automatically when there are no commands from the AV source, follow the steps
below.
To save energy, the panel can enter Standby automatically if there are no commands from the AV source for three
consecutive hours. At five minutes before and at every minute after that, a warning message appears on the
screen. When the final minute elapses, the panel switches to Standby.
To have the panel enter Standby automatically when there are no commands from the AV source, follow the steps
below.
1 ) Access
No Operation Off through the Power Control menu.
2 ) Select
Enable from No Operation Off menu.
3 ) Press HOME MENU to exit the menu.
PC Source -Power Management
When receiving signals from a PC, the panel can enter Standby automatically if the signal fails. Follow the steps
below to activate this function.
When receiving signals from a PC, the panel can enter Standby automatically if the signal fails. Follow the steps
below to activate this function.
1 ) Access
Power Management through the Power Control menu.
2 ) Select an option from the submenu.
Notes:
Pressing the remote’s MONITOR (a) button or the panel’s STANDBY/ON button reactivates the flat panel
display.
When the panel enters Standby with Mode 1 selected (no signals received), receiving signals again does
not cause the flat panel display to turn On.
When the panel enters the Power Management status with Mode 2 selected (no signals received),
receiving signals again causes the flat panel display to turn On.
display.
When the panel enters Standby with Mode 1 selected (no signals received), receiving signals again does
not cause the flat panel display to turn On.
When the panel enters the Power Management status with Mode 2 selected (no signals received),
receiving signals again causes the flat panel display to turn On.
3 ) Press HOME MENU to exit the menu.
These power management options are unavailable when a PC is connected to the panel through the HDMI port/
terminal.
For video and PC signals applicable to the flat panel display, see “9.2 Video/PC Signals (HDMI/DVI/Component/
min D-Sub/Composite).”
terminal.
For video and PC signals applicable to the flat panel display, see “9.2 Video/PC Signals (HDMI/DVI/Component/
min D-Sub/Composite).”
Option
Description
Off
no power management (default)
Mode 1
panel enters Standby when no signal is received
from the PC for
from the PC for
eight minutes, using the PC has no
effect on the panel
Mode 2
panel enters Standby when no signal is received
from the PC for
from the PC for
eight seconds, using the PC has no
effect on the panel
PRO-141FD_PRO-101FD.book Page 45 Monday, May 12, 2008 3:27 PM