Netgear 3200 전단

)NSTALLATION

Follow these instructions to install your NETGEAR® ReadyNAS™ 3200. Then, consult 
the ReadyNAS 3200 User Manual for instructions on configuring and operating your unit. 
A link to the ReadyNAS 3200 User Manual is on the Resource CD and on the NETGEAR 
support site at http://kbserver.netgear.com. The ReadyNAS Community forum at 
http://www.readynas.com/ is a valuable resource for accessing software updates, tips, use 
case guidelines, and more. The instructions in this guide assume the unit is using the 
factory default X-RAID2 disk configuration.
Estimated completion time: 20 minutes.
Note: A diskless unit requires installing disks and initializing RAID before proceeding. 
Go to http://kbserver.netgear.com for a list of supported disks. Refer to the ReadyNAS 
3200 User Manual for instructions on installing disks and configuring RAID. 

Follow these steps to set up the unit. Depending on the disks installed, the unit can weigh 
over 80 pounds (36 kg). Get assistance as needed for moving the unit.

Install the RAIDar utility from the product Resource CD. Windows, MAC and Linux 
versions of RAIDar are provided. 

For initial setup, connect the LAN1 Ethernet port of the ReadyNAS to your network, and 
turn it on. It takes about a minute to boot. By default it get its IP address via DHCP. 

1.  Run the RAIDar utility. It will discover units on the same subnet.
Tip: In your DHCP server, reserve the IP address assigned for your ReadyNAS so that it 

always gets this address. This helps assure that mapped drives work consistently on 
any operating system. 

2.  Click the RAIDar Setup button to open a FrontView browser 

session with the unit. The login screen will display. The default 
user name is admin and the password is netgear1. 

The FrontView configuration utility home page displays. 

The Setup Wizard will guide you 
through basic setup. Refer to the 
ReadyNAS 3200 User Manual for 
instructions on configuring options 
like backup, VLAN, or user 
accounts and quotas.
Note: If you choose to bypass the 
Setup Wizard, be sure to configure 
and alerts email address, change the 
admin password, and provide a 
password recovery question.
1.  In the factory default state, 

when logged in to the unit, Setup Wizard is enabled. Click Next to proceed with the 
wizard.

2.  On the Clock tab page, modify 

or accept the default timezone, 
time, and NTP options. Click 
Next to proceed. 

3.  On the Alerts tab page, provide 

at least one email address for 
system alerts. Click Next to 
proceed.

4.  On the Ethernet 1 tab page, 

accept or change the IP address 
settings.
Click Next to proceed.

5.  On the Global Settings tab page, you can modify the unit’s hostname. Also, if you 

will use a static IP configuration, you will need to configure the gateway and DNS 
settings (you do not have to change these settings if you use the unit in its default 
DHCP configuration). Click Next to proceed.

6.  On the Admin Password page, change the 

system login password, and provide a 
recovery question, answer, and email 
address. Note these changes. Click Next to 
proceed.

7.  On the Security Mode tab page, accept the 

default option of “User” which controls 
access to shares based on user or group 
accounts. FrontView will attempt to use the 
first workgroup name it discovers in the network. Otherwise, it will default to 
“VOLUME” as the workgroup name. Specify the workgroup name you want the unit 
to join. Refer to the ReadyNAS 3200 User Manual for ADS setup instructions. Click 
Next to proceed.

8.  On the Accounts page, click Add User. Add a new user and user password. Click 

Next to finish the wizard. Refer to the ReadyNAS 3200 User Manual for full 
instructions on setting up accounts. 

This completes the basic setup. Next, you will verify that you can access shares on your 
ReadyNAS.

Follow the steps below to access shares on the ReadyNAS. 

Note that, by default, these file sharing protocols are enabled: CIFS, AFP (advertised over 
both Bonjour and AFP), HTTP/S. FTP, NFS, iSCSI and Rsync are supported but are not 
enabled by default.

Refer to the ReadyNAS 3200 User Manual for instructions on accessing shares from Linux 
or Unix workstations, drive mapping, and other file sharing options, including unique 
language support for file names such as those that use unicode or ideographic characters. 

1.  To see a share listing in Windows, either click Browse in RAIDar or enter 

\\<ip_address> or \\<hostname> in the Windows Explorer address bar.