Samsung M8 사용자 설명서
Spinpoint M8 Product Manual REV 2.3
23
CHAPTER 5 DISK DRIVE OPERATION
This chapter describes the operation of the Spinpoint M8 hard disk drive functional subsystems. It is intended
as a guide to the operation of the drive, rather than a detailed theory of operation.
as a guide to the operation of the drive, rather than a detailed theory of operation.
5.1 Head / Disk Assembly (HDA)
The Spinpoint M8 hard disk drive consists of a mechanical sub-assembly and a printed circuit board
assembly (PCBA), as shown in Figure 5-1. This section describes the mechanism of the drive.
assembly (PCBA), as shown in Figure 5-1. This section describes the mechanism of the drive.
The head / disk assembly (HDA) contains the mechanical sub-assemblies of the drive, which are sealed
between the aluminum-alloy base and cover. The HDA consists of the base casting assembly (which
includes the DC spindle motor assembly), the disk stack assembly, the head stack assembly, and the rotary
voice coil motor assembly (which includes the actuator latch assembly). The HDA is assembled in a clean
room. These subassemblies cannot be adjusted or field repaired.
between the aluminum-alloy base and cover. The HDA consists of the base casting assembly (which
includes the DC spindle motor assembly), the disk stack assembly, the head stack assembly, and the rotary
voice coil motor assembly (which includes the actuator latch assembly). The HDA is assembled in a clean
room. These subassemblies cannot be adjusted or field repaired.
CAUTION: To avoid contamination in the HDA, never remove or adjust its cover
and seals. Disassembling the HDA voids your warranty.
and seals. Disassembling the HDA voids your warranty.
The Spinpoint M8 hard disk drive models and capacities are distinguished by the number of heads and
disks. The ST250LM004 have one (1) disk and two (2) read/write heads. The ST320LM001 have one (1)
disk and two (2) read/write heads. The ST500LM012 has one (1) disk and two (2) heads. The ST640LM001
have two (2) disks and four (4) read/write heads. The ST750LM022 have two (2) disks and four (4)
read/write heads. The ST1000LM024 has two (2) disks and four (4) read/write heads.
disks. The ST250LM004 have one (1) disk and two (2) read/write heads. The ST320LM001 have one (1)
disk and two (2) read/write heads. The ST500LM012 has one (1) disk and two (2) heads. The ST640LM001
have two (2) disks and four (4) read/write heads. The ST750LM022 have two (2) disks and four (4)
read/write heads. The ST1000LM024 has two (2) disks and four (4) read/write heads.
5.1.1 Base Casting Assembly
A one piece, aluminum-alloy base casting provides a mounting surface for the drive mechanism and PCBA.
The base casting also serves as the flange for the DC spindle motor assembly. A gasket provides a seal
between the base and cover castings that enclose the drive mechanism.
The base casting also serves as the flange for the DC spindle motor assembly. A gasket provides a seal
between the base and cover castings that enclose the drive mechanism.
5.1.2 DC Spindle Motor Assembly
The DC spindle motor assembly consists of the brush-less three-phase motor, spindle bearing (FDB)
assembly, disk mounting hub, and a labyrinth seal. The entire spindle mo to r assembl y is
completely enclosed in the HDA and integrated to the base casting. The labyrinth seal prevents bearing
assembly, disk mounting hub, and a labyrinth seal. The entire spindle mo to r assembl y is
completely enclosed in the HDA and integrated to the base casting. The labyrinth seal prevents bearing
lubricant from coming out into the HDA. The motor rotates the spindle shaft at 5400 rpm.