Drolet DB03122 사용자 설명서
Escape 1400 Insert Installation and Operation Manual
25
The gasket must be centred on the edge of the glass. To do this easily, peel back a
section of the paper covering the adhesive and place the gasket on a table with the
adhesive side up. Stick the end of the gasket to the middle of one edge, then press the
edge of the glass down onto the gasket, taking care that it is perfectly centred on the
gasket. Peel off more of the backing and rotate the glass and press the next section onto
the gasket. Do not stretch the gasket as you place it. Continue until you get to the start and
trim the gasket to length. Now pinch the gasket to the glass in a U shape, all around the
glass. Reinstall the glass, being careful to centre the glass carefully in the door. Do not
over-tighten the screws. Note that the two main causes of broken door glass are uneven
placement in the door and over-tightening of retaining screws.
section of the paper covering the adhesive and place the gasket on a table with the
adhesive side up. Stick the end of the gasket to the middle of one edge, then press the
edge of the glass down onto the gasket, taking care that it is perfectly centred on the
gasket. Peel off more of the backing and rotate the glass and press the next section onto
the gasket. Do not stretch the gasket as you place it. Continue until you get to the start and
trim the gasket to length. Now pinch the gasket to the glass in a U shape, all around the
glass. Reinstall the glass, being careful to centre the glass carefully in the door. Do not
over-tighten the screws. Note that the two main causes of broken door glass are uneven
placement in the door and over-tightening of retaining screws.
Do not abuse the glass door by striking or slamming shut. Do not use the insert if the glass
is broken. To change the glass, perform the same operation described above.
is broken. To change the glass, perform the same operation described above.
5.1.6 Cleaning and Painting the Insert
Do not attempt to clean or paint the insert when the unit is hot. Painted surfaces can
be wiped down with a damp cloth. Plated surfaces may be scratched by abrasive cleaners.
To maintain the finish at its original brilliance, use only a damp soft cloth to clean plated
surfaces.
Do not attempt to clean or paint the insert when the unit is hot. Painted surfaces can
be wiped down with a damp cloth. Plated surfaces may be scratched by abrasive cleaners.
To maintain the finish at its original brilliance, use only a damp soft cloth to clean plated
surfaces.
If the paint becomes scratched or damaged, you can give your wood insert a brand new
look by repainting it with heat-resistant paint. Before painting, roughen the surface with fine
sand paper, wipe it down to remove dust, and apply two thin coats of paint. For best
results, use the same paint that was originally used on the insert, which is available in
spray cans. See your dealer for details.
look by repainting it with heat-resistant paint. Before painting, roughen the surface with fine
sand paper, wipe it down to remove dust, and apply two thin coats of paint. For best
results, use the same paint that was originally used on the insert, which is available in
spray cans. See your dealer for details.
5.2 Chimney and Chimney Liner Maintenance
5.2.1 Why Chimney Cleaning is Necessary
Wood smoke can condense inside the chimney liner and chimney, forming a combustible
deposit called creosote. If creosote is allowed to build up in the venting system it can ignite
when a hot fire is burned in the insert and a very hot fire can progress to the top of the
chimney. Severe chimney fires can damage even the best chimneys. Smouldering, smoky
fires can quickly cause a thick layer of creosote to form. When you avoid smouldering so
the exhaust from the chimney is mostly clear, creosote builds up more slowly. Your new
insert has the right characteristics to help you to burn clean fires with little or no smoke,
resulting in less creosote in the chimney.
deposit called creosote. If creosote is allowed to build up in the venting system it can ignite
when a hot fire is burned in the insert and a very hot fire can progress to the top of the
chimney. Severe chimney fires can damage even the best chimneys. Smouldering, smoky
fires can quickly cause a thick layer of creosote to form. When you avoid smouldering so
the exhaust from the chimney is mostly clear, creosote builds up more slowly. Your new
insert has the right characteristics to help you to burn clean fires with little or no smoke,
resulting in less creosote in the chimney.