Cypress CY7C1525JV18 사용자 설명서
CY7C1510JV18, CY7C1525JV18
CY7C1512JV18, CY7C1514JV18
CY7C1512JV18, CY7C1514JV18
Document #: 001-14435 Rev. *C
Page 10 of 26
Truth Table
The truth table for CY7C1510JV18, CY7C1525JV18, CY7C1512JV18, and CY7C1514JV18 follows.
Operation
K
RPS WPS
DQ
DQ
Write Cycle:
Load address on the rising edge of K;
input write data on K and K rising edges.
Load address on the rising edge of K;
input write data on K and K rising edges.
L-H
X
L
D(A + 0) at K(t)
↑
D(A + 1) at K(t)
↑
Read Cycle:
Load address on the rising edge of K;
wait one and a half cycle; read data on C and C rising edges.
Load address on the rising edge of K;
wait one and a half cycle; read data on C and C rising edges.
L-H
L
X
Q(A + 0) at C(t + 1)
↑ Q(A + 1) at C(t + 2) ↑
NOP: No Operation
L-H
H
H
D = X
Q = High-Z
Q = High-Z
D = X
Q = High-Z
Q = High-Z
Standby: Clock Stopped
Stopped
X
X
Previous State
Previous State
Write Cycle Descriptions
The write cycle description table for CY7C1510JV18 and CY7C1512JV18 follows.
BWS
0
/
NWS
0
BWS
1
/
NWS
1
K
K
Comments
L
L
L–H
–
During the data portion of a write sequence
:
CY7C1510JV18
− both nibbles (D
[7:0]
) are written into the device.
CY7C1512JV18
− both bytes (D
[17:0]
) are written into the device.
L
L
–
L-H During the data portion of a write sequence
:
CY7C1510JV18
− both nibbles (D
[7:0]
) are written into the device.
CY7C1512JV18
− both bytes (D
[17:0]
) are written into the device.
L
H
L–H
–
During the data portion of a write sequence
:
CY7C1510JV18
− only the lower nibble (D
[3:0]
) is written into the device, D
[7:4]
remains unaltered.
CY7C1512JV18
− only the lower byte (D
[8:0]
) is written into the device, D
[17:9]
remains unaltered.
L
H
–
L–H During the data portion of a write sequence
:
CY7C1510JV18
− only the lower nibble (D
[3:0]
) is written into the device, D
[7:4]
remains unaltered.
CY7C1512JV18
− only the lower byte (D
[8:0]
) is written into the device, D
[17:9]
remains unaltered.
H
L
L–H
–
During the data portion of a write sequence
:
CY7C1510JV18
− only the upper nibble (D
[7:4]
) is written into the device, D
[3:0]
remains unaltered.
CY7C1512JV18
− only the upper byte (D
[17:9]
) is written into the device, D
[8:0]
remains unaltered.
H
L
–
L–H During the data portion of a write sequence
:
CY7C1510JV18
− only the upper nibble (D
[7:4]
) is written into the device, D
[3:0]
remains unaltered.
CY7C1512JV18
− only the upper byte (D
[17:9]
) is written into the device, D
[8:0]
remains unaltered.
H
H
L–H
–
No data is written into the devices during this portion of a write operation.
H
H
–
L–H No data is written into the devices during this portion of a write operation.
Notes
2. X = “Don't Care,” H = Logic HIGH, L = Logic LOW,
↑
represents rising edge.
3. Device powers up deselected with the outputs in a tri-state condition.
4. “A” represents address location latched by the devices when transaction was initiated. A + 0, A + 1 represents the internal address sequence in the burst.
5. “t” represents the cycle at which a Read/Write operation is started. t + 1, and t + 2 are the first, and second clock cycles respectively succeeding the “t” clock cycle.
6. Data inputs are registered at K and K rising edges. Data outputs are delivered on C and C rising edges, except when in single clock mode.
7. It is recommended that K = K and C = C = HIGH when clock is stopped. This is not essential, but permits most rapid restart by overcoming transmission line charging
4. “A” represents address location latched by the devices when transaction was initiated. A + 0, A + 1 represents the internal address sequence in the burst.
5. “t” represents the cycle at which a Read/Write operation is started. t + 1, and t + 2 are the first, and second clock cycles respectively succeeding the “t” clock cycle.
6. Data inputs are registered at K and K rising edges. Data outputs are delivered on C and C rising edges, except when in single clock mode.
7. It is recommended that K = K and C = C = HIGH when clock is stopped. This is not essential, but permits most rapid restart by overcoming transmission line charging
symmetrically.
8. Is based on a write cycle that was initiated in accordance with the
table. NWS
0
, NWS
1,
BWS
0
, BWS
1,
BWS
2
and BWS
3
can be altered on
different portions of a write cycle, as long as the setup and hold requirements are achieved.