Cypress CY7C1443AV33 사용자 설명서
CY7C1441AV33
CY7C1443AV33,CY7C1447AV33
Document #: 38-05357 Rev. *G
Page 7 of 31
Pin Definitions
Name
IO
Description
A
0
, A
1
, A
Input-
Synchronous
Address Inputs Used to Select One of the Address Locations. Sampled
at the rising edge of the CLK if ADSP or ADSC is active LOW, and CE
at the rising edge of the CLK if ADSP or ADSC is active LOW, and CE
1
,
CE
2
,
and
CE
3
are sampled active. A
[1:0]
feed the 2-bit counter.
BW
A
, BW
B
BW
C
, BW
D
,
BW
E
, BW
F
,
BW
G
, BW
H
Input-
Synchronous
Byte Write Select Inputs, Active LOW. Qualified with BWE to conduct byte
writes to the SRAM. Sampled on the rising edge of CLK.
writes to the SRAM. Sampled on the rising edge of CLK.
GW
Input-
Synchronous
Global Write Enable Input, Active LOW. When asserted LOW on the rising
edge of CLK, a global write is conducted (ALL bytes are written, regardless
of the values on BW
edge of CLK, a global write is conducted (ALL bytes are written, regardless
of the values on BW
X
and BWE).
CLK
Input-
Clock
Clock Input. Used to capture all synchronous inputs to the device. Also used
to increment the burst counter when ADV is asserted LOW, during a burst
operation.
to increment the burst counter when ADV is asserted LOW, during a burst
operation.
CE
1
Input-
Synchronous
Chip Enable 1 Input, Active LOW. Sampled on the rising edge of CLK. Used
in conjunction with CE
in conjunction with CE
2
and CE
3
to select/deselect the device. ADSP is
ignored if CE
1
is HIGH. CE
1
is sampled only when a new external address is
loaded.
CE
2
Input-
Synchronous
Chip Enable 2 Input, Active HIGH. Sampled on the rising edge of CLK. Used
in conjunction with CE
in conjunction with CE
1
and CE
3
to select/deselect the device. CE
2
is sampled
only when a new external address is loaded.
CE
3
Input-
Synchronous
Chip Enable 3 Input, Active LOW. Sampled on the rising edge of CLK. Used
in conjunction with CE
in conjunction with CE
1
and CE
2
to select/deselect the device. CE
3
is
assumed active throughout this document for BGA. CE
3
is sampled only when
a new external address is loaded.
OE
Input-
Asynchronous
Output Enable, Asynchronous Input, Active LOW. Controls the direction
of the IO pins. When LOW, the IO pins behave as outputs. When deasserted
HIGH, IO pins are tri-stated, and act as input data pins. OE is masked during
the first clock of a read cycle when emerging from a deselected state.
of the IO pins. When LOW, the IO pins behave as outputs. When deasserted
HIGH, IO pins are tri-stated, and act as input data pins. OE is masked during
the first clock of a read cycle when emerging from a deselected state.
ADV
Input-
Synchronous
Advance Input Signal, Sampled on the Rising Edge of CLK. When
asserted, it automatically increments the address in a burst cycle.
asserted, it automatically increments the address in a burst cycle.
ADSP
Input-
Synchronous
Address Strobe from Processor, Sampled on the Rising Edge of CLK,
Active LOW. When asserted LOW, addresses presented to the device are
captured in the address registers. A
Active LOW. When asserted LOW, addresses presented to the device are
captured in the address registers. A
[1:0]
are also loaded into the burst counter.
When ADSP and ADSC are both asserted, only ADSP is recognized. ASDP
is ignored when CE
is ignored when CE
1
is deasserted HIGH
ADSC
Input-
Synchronous
Address Strobe from Controller, Sampled on the Rising Edge of CLK,
Active LOW. When asserted LOW, addresses presented to the device are
captured in the address registers. A
Active LOW. When asserted LOW, addresses presented to the device are
captured in the address registers. A
[1:0]
are also loaded into the burst counter.
When ADSP and ADSC are both asserted, only ADSP is recognized.
BWE
Input-
Synchronous
Byte Write Enable Input, Active LOW. Sampled on the rising edge of CLK.
This signal must be asserted LOW to conduct a byte write.
This signal must be asserted LOW to conduct a byte write.
ZZ
Input-
Asynchronous
ZZ “sleep” Input, Active HIGH. When asserted HIGH places the device in
a non-time-critical “sleep” condition with data integrity preserved. For normal
operation, this pin must be LOW or left floating. ZZ pin has an internal pull
down.
a non-time-critical “sleep” condition with data integrity preserved. For normal
operation, this pin must be LOW or left floating. ZZ pin has an internal pull
down.