AMCC 9590SE-4ME 사용자 설명서
Chapter 2. CLI Syntax Reference
54
3ware Serial ATA RAID Controller CLI Guide for the Power Mac G5
One application of the /cx/ux show command is to see which sub-unit of a
degraded unit has caused the unit to degrade and which disk within that sub-
unit is the source of degradation. Another application is to see the source and
destination units during a migration.
degraded unit has caused the unit to degrade and which disk within that sub-
unit is the source of degradation. Another application is to see the source and
destination units during a migration.
Example:
//localhost> /c0/u1 show
Unit UnitType Status %Cmpl Port Stripe Size(GB) Blocks
----------------------------------------------------------------------
u1 RAID-0 OK - - 64K 3576.06 7499550720
u1-0 DISK OK - p0 - 298.01 624962560
u1-1 DISK OK - p1 - 298.01 624962560
u1-2 DISK OK - p2 - 298.01 624962560
u1-3 DISK OK - p3 - 298.01 624962560
u1-4 DISK OK - p4 - 298.01 624962560
u1-5 DISK OK - p5 - 298.01 624962560
u1-6 DISK OK - p6 - 298.01 624962560
u1-7 DISK OK - p7 - 298.01 624962560
u1-8 DISK OK - p8 - 298.01 624962560
u1-9 DISK OK - p9 - 298.01 624962560
u1-10 DISK OK - p10 - 298.01 624962560
u1-11 DISK OK - p11 - 298.01 624962560
u1/v0 Volume - - - - 2047.00 4292870144
u1/v1 Volume - - - - 1529.06 3206680576
/c
x
/u
x
show
attribute
[
attribute
...]
This command shows the current setting of the specified attributes. One or
many attributes can be requested. Specifying an invalid attribute will
terminate the loop. Possible attributes are: initializestatus, name (9000 series),
qpolicy (9550SX and 9590SE only), rebuildstatus, serial (9000 series), status,
storsave (9550SX and 9590SE only), verifystatus, volumes (9000 series),
autoverify (9000 series), cache, ignoreECC (9000 series), and identify
(9550SX and 9590SE only).
many attributes can be requested. Specifying an invalid attribute will
terminate the loop. Possible attributes are: initializestatus, name (9000 series),
qpolicy (9550SX and 9590SE only), rebuildstatus, serial (9000 series), status,
storsave (9550SX and 9590SE only), verifystatus, volumes (9000 series),
autoverify (9000 series), cache, ignoreECC (9000 series), and identify
(9550SX and 9590SE only).
/c
x
/u
x
show status
This command reports the status of the specified unit.
Possible statuses include: OK, VERIFYING, VERIFY-PAUSED,
INITIALIZING, INIT-PAUSED, REBUILDING, REBUILD-PAUSED,
DEGRADED, MIGRATING, MIGRATE-PAUSED, RECOVERY,
INOPERABLE, and UNKNOWN. (Definitions of the unit statuses are
available in the 3ware Serial ATA RAID Controller User Guide.)
INITIALIZING, INIT-PAUSED, REBUILDING, REBUILD-PAUSED,
DEGRADED, MIGRATING, MIGRATE-PAUSED, RECOVERY,
INOPERABLE, and UNKNOWN. (Definitions of the unit statuses are
available in the 3ware Serial ATA RAID Controller User Guide.)
Example:
//localhost> /c0/u0 show status
/c0/u5 status = OK