ATTO Technology V-Class 사용자 설명서
44
Configure drives with CLI commands
DriveWipe
Initializes a drive: wipes it of all data. Drive must be
offline
Initializes a drive: wipes it of all data. Drive must be
offline
Set syntax: DriveWipe [Destination Sled] [Dest Drive]
Requires a SaveConfiguration Restart command
Get syntax: DriveCopyStatus
Requires a SaveConfiguration Restart command
Get syntax: DriveCopyStatus
IdeTransferRate
Sets the DMA mode transfer rate for all devices.
Sets the DMA mode transfer rate for all devices.
Choices: 0, 1, 2, 3, 4
Default: 4
Set syntax: set IdeTransferRate [0 | 1 | 2 | 3 | 4]
Requires a SaveConfiguration Restart command
Get syntax: get IdeTransferRate
Requires a SaveConfiguration Restart command
Get syntax: get IdeTransferRate
LUNInfo
Displays information about all LUNs (logical unit
numbers) or detailed information about a specific LUN.
Do not specify a LUN to get information about all LUNs.
Specify a LUN to get detailed information about that
individual LUN. For examples, Refer to Diagnostic
Commands on page 41.
Displays information about all LUNs (logical unit
numbers) or detailed information about a specific LUN.
Do not specify a LUN to get information about all LUNs.
Specify a LUN to get detailed information about that
individual LUN. For examples, Refer to Diagnostic
Commands on page 41.
...
Get syntax: get LUNInfo [LUN]
LUNState
Sets the LUN to the specified state. May be used to
facilitate removal and insertion of sleds and RAID groups
during power up/power down of sleds.
Sets the LUN to the specified state. May be used to
facilitate removal and insertion of sleds and RAID groups
during power up/power down of sleds.
Default: online
Set syntax: set LUNState [LUN number] [online|offline]
Get syntax: get LUNState [LUN number]
Set syntax: set LUNState [LUN number] [online|offline]
Get syntax: get LUNState [LUN number]
PartitionCommit
Commits the current Planned Partition Configuration,
making it the persistent, Active configuration.
PartitionCommit must be used to alter any partition
settings. Performs a firmware restart.
Commits the current Planned Partition Configuration,
making it the persistent, Active configuration.
PartitionCommit must be used to alter any partition
settings. Performs a firmware restart.
Immediate command: PartitionCommit
Information: PartitionInfo
Information: PartitionInfo
PartitionInfo
Displays Partition information for the selected partitions.
Refer to Diagnostic Commands on page 41 for examples.
Displays Partition information for the selected partitions.
Refer to Diagnostic Commands on page 41 for examples.
Immediate command: PartitionInfo [active|planned]
[Virtual Drive ID] [Partition ID]
[Virtual Drive ID] [Partition ID]
PartitionMerge
Merges the specified partitions into a single larger
partition. All partitions to be merged must be stored on
contiguous sections of the specified Virtual Drive. If you
want this configuration to become the active
configuration, follow with a PartitionCommit command.
Merges the specified partitions into a single larger
partition. All partitions to be merged must be stored on
contiguous sections of the specified Virtual Drive. If you
want this configuration to become the active
configuration, follow with a PartitionCommit command.
Set syntax: PartitionMerge [Virtual Drive ID] [Partition
ID|all] [<Partition number...>]
Requires a PartitionCommit command
Information: PartitionInfo
ID|all] [<Partition number...>]
Requires a PartitionCommit command
Information: PartitionInfo
PartitionSplit
Create or modify partitions on a Virtual Drive. If you
want this configuration to become the active
configuration, follow with a PartitionCommit command.
Create or modify partitions on a Virtual Drive. If you
want this configuration to become the active
configuration, follow with a PartitionCommit command.
Set syntax: PartitionSplit [Virtual Drive ID] [Partition ID]
[Number of partitions]
Requires a PartitionCommit command
Information: PartitionInfo
[Number of partitions]
Requires a PartitionCommit command
Information: PartitionInfo
QuickRAID0
Specifies the RAID Level 0 configuration for the system.
The default 0, or no RAID groups, configures the
Diamond Storage Array in a JBOD configuration.
DRIVE indicates drives on one side of the array are
adjacent members of the same stripe group while SLED
indicates the two drives on the same sled are adjacent
members of a stripe group.
Specifies the RAID Level 0 configuration for the system.
The default 0, or no RAID groups, configures the
Diamond Storage Array in a JBOD configuration.
DRIVE indicates drives on one side of the array are
adjacent members of the same stripe group while SLED
indicates the two drives on the same sled are adjacent
members of a stripe group.
Choices: 0, 1, 2, 3, 4, 6,12
Set syntax: set QuickRAID0 [0|1|2|3|4|6|12][drive| sled]
Requires a SaveConfiguration Restart command
Information: DriveInfo
Set syntax: set QuickRAID0 [0|1|2|3|4|6|12][drive| sled]
Requires a SaveConfiguration Restart command
Information: DriveInfo
QuickRAID1
Specifies the RAID Level 1 configuration for the system.
Sets the system to a mirrored array of spanned drives.
Causes the Configuration Manager to “stamp” the new
configuration onto the drives to take effect at the next
system startup. Setting QuickRAID0 0 removes all RAID
Specifies the RAID Level 1 configuration for the system.
Sets the system to a mirrored array of spanned drives.
Causes the Configuration Manager to “stamp” the new
configuration onto the drives to take effect at the next
system startup. Setting QuickRAID0 0 removes all RAID