Cisco Systems NPE-225 사용자 설명서
7-63
Network Processing Engine and Network Services Engine Installation and Configuration
OL-4448-12
Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information
Upgrading ROMmon on the NPE-G1 or NPE-G2
Step 3
Copy the boot helper image from the TFTP server to flash memory as follows:
router# copy tftp bootflash:
Address or name of remote host []? biff
Source filename []? c7200-boot-mz.120-5.S
Destination filename [c7200-boot-mz.120-5.S]?
Accessing tftp://biff/c7200-boot-mz.120-5.S...
Loading c7200-boot-mz.120-5.S from 192.168.254.254 (via
Ethernet4/0):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 3132516/6264832 bytes]
3132516 bytes copied in 28.488 secs (111875 bytes/sec)
This completes the procedure for upgrading your boot helper (boot loader) image. For more detailed
instructions on loading and maintaining system images and microcode, including boot helper images,
refer to the Configuration Fundamentals Configuration Guide, which is available on Cisco.com.
instructions on loading and maintaining system images and microcode, including boot helper images,
refer to the Configuration Fundamentals Configuration Guide, which is available on Cisco.com.
Upgrading ROMmon on the NPE-G1 or NPE-G2
Upgrading the rewriteable ROM monitor (ROMmon) allows you to download a new ROMmon image
instead of having to replace hardware (NPE-G1 or NPE-G2) to get a new image.
instead of having to replace hardware (NPE-G1 or NPE-G2) to get a new image.
Note
ROMmon can be upgraded on the NPE-G1 or NPE-G2, but cannot be upgraded on any other network
processor engine for the Cisco 7200 series routers.
processor engine for the Cisco 7200 series routers.
There are two ROMmon images: one ReadOnly image (the original image that shipped with your
system) that is always available if you have the following:
system) that is always available if you have the following:
•
NPE-G1 hardware EPROM version 4.0 with NPE-G1 ROMmon version 12.3(4r)T1 or later
•
NPE-G2 hardware
You can choose to configure the system to point to the second ROMmon image, the upgradeable
ROMmon image. At bootup, the system starts with the ReadOnly image and then, if configured, jumps
to the upgradeable image. If the upgradeable ROMmon image fails to boot, the router will mark this
ROMmon image as invalid and revert to the ReadOnly image.
ROMmon image. At bootup, the system starts with the ReadOnly image and then, if configured, jumps
to the upgradeable image. If the upgradeable ROMmon image fails to boot, the router will mark this
ROMmon image as invalid and revert to the ReadOnly image.
The first time a new ROMmon image is executed, you must allow the system to boot ROMmon before
doing any additional resets or power cycling. If the ROMmon-executing process is interrupted, the stem
interprets this as a bootup failure of the new ROMmon image. The router reverts to the ReadOnly image.
doing any additional resets or power cycling. If the ROMmon-executing process is interrupted, the stem
interprets this as a bootup failure of the new ROMmon image. The router reverts to the ReadOnly image.
Note
The ROMmon upgrade image is marked as invalid if it fails to boot. Do not reset the router when it is
performing an initial bootup.
performing an initial bootup.